Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
I am trying to program my nRF51 QFAC, but it tells me to adjust my linker settings.
I am using the SDK 12.3 and the softdevice 130 2.0.1.
However, after I apply the...
MCU : nrf52833
SDK : Ver 17.1.0
SoftDevice : S140
I try to call RTC value to external RTC Module by TWIM in BLE authentication rw request event.
But MCU stop to...
Good afternoon,
I built and flashed the Bluetooth Multiple advertising sets sample in VS Code using the nRF Connect Extension Pack onto my nRF5340-DK and come across an...
I am trying to measure my battery level on my nRF51822 beacon board through the internal ADC.
The chip is just advertising itself every 5 seconds.
The measurement works...
Hello,
I am trying to develop a low-power application based on the direct test mode example. I saw in this blogpost: https://devzone.nordicsemi.com/nordic/nordic-blog...
Hi there,
We are currently developing and testing on the nRF5340. We are using our own OS (not Zephyr).
We measure power on the devkit by connecting the PPK2 as a source...
Good day I am wondering if anyone can help me
For background information.
Network - NB-iot
Firmware - 1.3.1
Software - Serial LTE Modem
Hardware - nrf9160dk
...
Hi,
i wanted to i2c interface of nrf with adc ic 3427. i am trying to interface by refer example of twi_scanner device address get found correctly.
now i am trying to...
On an nRF52840 using SDK 15.3 and FreeRTOS 10
I've got both a PCA10056 dev kit and a custom board. I don't think I've got a hardware issue here but I'm running the usb_msc_pca10056...
How do I use printf to output my own messages, and read incoming data, from a UART port that is separate from Zephyr's debugging outputs? This UART line will be connected...
Hi guys,
I have developed a custom board using the nRF52840 module and the SDK16.If the peripheral is disconnected from the central, it starts advertising again in normal...
I have a custom nRF52480 board and addded mesh functionality based on the light mesh sample
The app crashes during provisioning from the nRF Mesh app.
Relevant portion...
Hello,
I would like to enter simple commands such as on, off to the USB CDC ACM, and then set the parameters in the model through string comparing.
(now i'm trying Generic...
Hello Team,
We are interfacing nRF52832 with an external flash for data storage. Could you please point to the right document/link/code reference on how to interface external...
Hello,
I tested QDEC0 using the zephyr qdec sample (which uses the nrfx_qdec driver) and a DC motor with a built-in encoder.
Below you will see the overlay file configuration...
