Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
SDK: NCS 1.9.0
Hardware(peripheral): nRF52832
Central: iPhone(iOS)
IDE: SES
Hi,
I am trying to configure our project to accept re-pairings from the central but I...
I am using an nRF52840 and communicating with an ESB. Packets are sent one-way from tx to rx every 1 ms.
What is the conversion of RSSI to dBm?
In the data sheet, as ...
Hi,
In one of the ble example , it is using generic on_off_srv.c and .h files. along with health and generic server. we have requirement that we need to write unit test...
Hello, as stated in the Title im trying to establish UART Communication betwenn a nRF52840 DK and a nRF9160 DK. I need to use the Asynchronous API otherwise there are no other...
Hi Team,
we are working on smart remote 3 implementation using nRF52832 with Windows operating system.
we want to implement NVS. how to do with Windows OS?
I need to define a function to print message and register to other module. In my application, NRF_LOG is used by most modules so I need to use NRF_LOG to construct this printf...
Hi,
I tested Extended advertising for my data using sdk connect 1.9.1 and 1.8.0, the code is attached.
With both the SDK, I observed different behaviour. First of all...
I am running segger embedded studio 5.63a on NRF52832 and 52840 using SDK 16.0. We want to update SES to the newest tools compatible with SDK 16.0. We loaded version 6.22a...
Hi
We have some production equipment still running windows 7. We would like to update the nrf51 dongle to a nrf52 dongle.
But drivers for nrf52 dongle is not installed...
I have been doing some measurements on the execution time of my code and noticed something strange.
Currently, I am using an application timer to trigger the ADC to sample...
How to implement unpaired binding whitelist? I have tried, but the device that only sets the MAC address whitelist cannot be connected, so I must set the peer IRK. Is there...
Hello,
I'm just learning the nRF stack and development environment, hopefully this question is not too basic. Our product requires the usage of the extended data length...
Hi there
I am testing the ATT MTU throughput test provided by nRF5 SDK and I found the throughput could not reach the theoretical maximum 1.4Mbps.
Hence, I used the...
