Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I working on Asset_tracker_v2. I need to add event based custom module to the application Asset_tracker_v2. I created follwoing files:
A. In the src/events folder
1. bms_event_module...
Hello,
I am new to Zephyr and its ecosystem which includes MCUboot and also the NCS sdk. I have a question regarding the nRF5340 bootloader.
So we already have a product...
I had to upgrade SoftDevice and application firmware from v6.1.1 to v7.2.0 in order to have BLE_GATTC_OPT_UUID_DISC option available.
It turned out that Bootloader needs...
Hi,
I want to implement a BLE function that a master can connect to multiple slaves at the same time，and the services are located at the master，do I need to create multiple...
I'm having some (minor) trouble with a board based on an NRF52840 that I want to start running as soon as power is applied...
This is built using a RAK5010 board, but using...
So I just got past the hurdle I had when trying to do extended advertising in the following support thread, and now I have a new problem along the same lines:
https://devzone...
Hi All,
We are planning to use MAX 3051(CAN Transceiver) which will be interfaced with the NRF52832 over UART.
Our goal is to decode the incoming CAN messages from the...
I had been using the Andoid 4.24.3 version of the nRF Connect app and had no problem with performing DFUs. With the newer 4.25.1 version of the app I noticed a few things...
While trying to reply further queries, by mistake, above ticket got closed ... So, I need to discuss more to the reted issue in the ticket. When, there is a click on verify...
Hello,
I'm trying to add credential to the modem on the nrf9160. However, i keep getting a -111 error when i'm trying to connect to my server with TLS mode.
When i try...
Hi
I connected the nRF21540 to a nRF52840 like in the application notes.
Here is the schematic:
I implemented the driver and now I try to communicate over the SPI...
Hi
I'm using the PA LNA driver for the nRF21540 with the function:
void mesh_lna_setup_start(uint32_t rampup_start_capture_time, uint32_t timer_index)
Now, when I check...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
Hi team !
I'm facing issue when porting my code from nRF52840DK to nRF5340DK
I implemented SAADC acquisition, using Timer/SAADC/(D)PPI stack on both boards, handling...
