hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
Is there any way that a BLE event handler installed with NRF_SDH_BLE_OBSERVER, can stop the execution of other (following) observers?
I have various modules using their...
Hi
I am a student and this is my first project working on BLE. Please keep that in mind.
The end goal is to create a fingerprinting system with a Thingy (nRF6936) as...
I have modified the BLE app Blinky example so that the LED is enabled (state 1) on power up. However, this is not being reflected on the BLE side because when I connect with...
Hi, when debugging, I'm encountering this problem where relevant SPI registers (likely status registers) signaled a successful read before the actual data could be pulled...
We're developing a mobile application which will communicate with a satellite antenna over BLE. We will not have access to the antenna for a few months, and therefore we aquired...
I am using the UART to perform serial DFU on nRF52832. I got it to work fine using nRF Connect SDK 1.8.0.
Now, I need to pass some serial data to the APP when not in DFU...
Hi, I have to develop a new nRF5340/Zephyr/MCUBoot-based device that communicates with a Windows application via USB. The Windows application already manages other legacy...
Hello,
I'm trying to implement a set up of the ble device name from the NVMC UICR register.
But when I try to take it from the register and to set it has a name, it doesn...
Hi,
when using the spi peripheral in slave configuration, what can I expect at power consumption level? does the spi peripheral derive its clock from an internal system...
Hello,
I am using nRF52840 DK's P20 SWD to communicate with an external nRF52840 board . My setup works fine with nrfjprog running from command line. To communicate with...
Is there any example code using a QSPI image as the input for the bootloader instead of e.g. BLE? What format does that have to be in to begin with? Currently doing DFU updates...
Hello friends
I am fresher for Nordic semiconductor . I want to interface triaxial accelerometer of 15MHZ frequency with nrf52840 with inbuilt ADC and transmit the data...
Hello,
I will try to use the macro ZB_ZCL_SET_MODIFY_ATTR_VALUE_CB to define a callback when an attribut is written in my device. But the callback I write is never called...
I had a look on APIs to use UART in Zephyr in the link https://docs.zephyrproject.org/latest/reference/peripherals/uart.html#uart-interrupt-api . There are three types: Poll...
