hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I have a JDY-16 BLE chip in AT command mode and are able to scan for a SoftRF device that has a Nordic UART service.
I can succesfully see the SoftRF device during a scan...
Hi All,
Currently I'm editing an example project using the NRF5 SDK in SES -- however, I'm not sure exactly how to best version a project or even export it to contain...
I am developing a product using SDK_17.1.0 and nRF52805. The basic function development has been completed.
I need the DTM firmware for RF test of the nRF52805 board, so...
Hi,
For my nRF52840 custom board, when I send data through app_usbd_cdc_acm_write() to the serial port from main.c , data are transferred without problem but
when I try...
Hello,
I just recently updated to Windows 11 and facing the issue(nrfutil is not working) after win11 update. Previously, It is worked on Win10. Do you have the working...
Hi.
nRF52-DK board use. (PCA10040)
* now system : bootloader + softdevice + Beacon application ->> working fine. good.
* new system : Swtiching ESB or Beacon
I would...
When I connected mqtt on nRF9160, I found a strange problem, which caused the device to freeze and become bricked. The location cause was found to appear in err = mqtt_connect...
Hello, we are semi-experienced with Nordic,
We are doing a DC power driver, during operation we do a NUS data send if we are connected and the NUS has started. When we get...
Hello,
I am trying to optimize GPS power consumption, and the fix time. The GPS search period is approximately 10 minutes, modem fw 1.3.1 and nRF SDK 1.7.0. We are also...
Hi Nordic，
is the encryption technology used in the software protocol or hardware inside 52833?
our customer want to know the if the encryption can export,thank you！
I baught new DK. Form last few days, I was testing sample programs for learning purpose. Suddenly, SDK stopped being detcected via USB port ? I could not diagnose the reason...
I got this error during development.
I think it is caused by the BLE device erasing the connection information with iOS,
I don't know under what circumstances the BLE...
Hi
I want to increase the number of leds in DTS file of peripheral-uart sample by using overlay file.
Is it possible to manipulate the aliases in DTS file by editing the...
I'm running in to the issue mentioned in the tile; " Only spi nodes accepted in /soc/spi@40023000/". I'm using nRF connect and built a driver for the TI ADS1291 analog front...
Hi, I read a couple of post that asked about the accuracy / tolerance of the internal REF, and the answers mention it's included in the gain error.
This made me wondering...
