hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
In our Android app, we want to throttle back MTU size when the error rates get too high. However, the app is crashing with NRF_ERROR_INVALID_STATE when we try to send the...
Hello everyone,
I am using the SDK 17.1 with the NRF52832 chip. My current project is created based on the multirole example. My first step was to implement writing and...
Hi Nordic team,
Our requirement is creating two TLS server with same IP and different port no, but when I try to bind two servers only one server is getting bind to the...
Hi,
I have set up the PWM to trigger the ADC via PPI. It works but now i want to verify the exact behaviour by setting a GPIO when the ADC starts a conversion and when it...
Hi Nordic
I want to confirm whether this function pm_peer_id_get will return PM_PEER_ID_INVALID if nrf52833 has never been bound to a mobile phone when obtaining the peer...
I want to speed up the ble transfer, use the ble_app_uart example, but the speed is too low , sniffer show that the notify pack moredata is true , but the follow pack is not...
Hello,
as far as I know the TLS implementation in the NRF9169 MFW does currently not support Connection Identifiers for DTLS 1.2 .
Are there any plans or a timeline when...
I have a nRF9160 DK (sn 000960004886) that has been working fine, I've tested out to build and load some of the application samples (blinky, hello_world) and they all worked...
Hey!
I am programming on the nrf52dk connected with debug out with an HW using the nrf52805 BLE soc.
My Colleague is already programming with the Segger Embedded Studio...
[Bootloader is based on NRF SDK v11]
I am experimenting with the NRF SDK v11 bootloader source code and want to trigger the UART/serial DFU as the bootloader starts. Right...
hi,
I am running openthread coap_client sample from NRFconnect SDK v1.6.1 and I have enabled joiner in my code.
But still, when I flash the code on nrf52840dk_board, it...
Hi!
I am working on a project with NRF51422QFAB.
First I tried a simple program, which runs well.
After that I would like to try out my own board antenna with the...
Hello everyone!
This is actually more a suggestion to improve flexibility for NCS integration (i.e. nrf-sdk) into Zephyr workspaces. In many CMake- and Kconfig files there...
This relates to playing audio files over i2s.
So far I have managed to replay audio files using the method suggested in the SDK i2s example files - basically sending one...
Hello,
I have an own hardware using nRF5340. So I created first an own board in the device tree. I took the definition of the nRF5340 development board and simply removed...
