I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I'm using the nRF52840 on a custom board along with an ESP8266 (ESP-12S) Wi-Fi module.
The ESP module prints out a bunch of information at a weird nonstandard baud...
I am having trouble setting up DFU over BLE in nRF Connect SDK. I am using NCS 1.9.1. I have followed these instructions with my own project on both the nrf52840 devkit and...
Dear All,
We are developing a device based around nRF52840 on a rigid-flex custom PCB that is mounted inside an anodized aluminum cube with one face covered with plastic...
Hello, I'm trying to get an LPN to unprovision itself based off of an external command. I tried to base it off of the examples so I simply call: However after the reset it...
Hi,
I have my device based on the nRF52840, we have manufactured some equipments and we have created our own application to manage connection. Everything is working fine...
Hi all,
we recently had a problem with couple of our boards based on Raytac MDBT50Q-1MV2 (nrf52840 + osc. + antenna). We base our app on Zephyr. After programming some boards...
Hi, I've been tasked with doing some development on the nRF24LE1F on one of our legacy products that was designed many years ago! I'm in process of converting the code to...
Hi,
I'm trying to use UART1 for console and shell, for example to be able to log messages on VCOM0 linked to UART1 of my nRF5340 DK board. The example that I'm testing is...
Hi Nordic team
Customer Delta was running a street lamp project.
For AWS FOTA, they applied a AWS account and firmware update already can work.
However, it looks like...
Hello,
I am developing FW on NRF52840_DK for a BLE Peripheral as a Reader.
Reader to Mobile App Tx size is 32 bytes
Mobile App to Reader Rx size is 133 bytes.
When...
Dear Bluetooth Mesh experts, The firmware contains a proprietary message that sets a node's parameters and returns 100 bytes of data. The Android app sends it as an acknowledged...
Hi
I've configured Zephyr to run BLE host on cpuapp and BLE controller on cpunet, and using RPMsg to communicate between them.
When I call bt_enable() from the app core...
Hello,
I was wondering if there is a way to extract the "Device name" from the scanned advertisement data published by a model on a different node. I want to display the...
I'm trying to enable saving of coredump to flash. I'm running on nrf52840 with NRF SDK 1.6.1.
I have defined the following:
CONFIG_DEBUG_COREDUMP=y
CONFIG_DEBUG_COREDUMP_BACKEND_FLASH_PARTITION...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
