Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
I have builded a circuit with a nRF52DK and a mpu9250 IMU. If I power the Sensor with VDD the Zephyr driver and all of the Software performs well and the values from...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
Hi All,
I'm using nrf Connect SDK v1.7.0 with Vs Code
So here I can see in the debug prints that Bluetooth device is able to get connection successfull callback and Immediately...
Hi everyone,
I have a preblem for BLE Mesh 5.0 version (board is nrf52840),
I found that in the Setting set function of the Sensor Model, it seems that the data is transmitted...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
Hello everybody,
we are currently working with an nRF51822 mounted on a Adafruit Bluefruit LE UART Friend. We use pca 10028 and s130.
While debugging through the code...
I am developing for a Thingy91 and NRF9160 DK
NCS v 1.9.1
I was initially using the LTE_BLE_Gateway sample with the NRF52840 running the hci_lpuart sample. and that...
Hi Devzone
Currently for my customer request , they would like use the nrf91 on their wearable.
They would like to do NRF91 FOTA with the external flash SPI w25q128jv...
Hello,
I use ncsv1.9.1 and segger embedded studio.cmd to open a nRF connect SDK, but there is an error: S yntaxError: Unable to parse JSON string .
I replace SES and...
Hi, My current application is using a softdevice and I need to update it using DFU to an application without softdevice.
The new application must start at 0x0 address, so...
Hello guys,
I am using the nRF52 DK.
I have to connect a spi sensor which is already made.
This part works. ("nrf_drv_spi.h" fyi)
I also have to store the info...
Hi, I'm using the Adafruit ble sniffer (V2.0, black board), with the nRF51822, and I can sniff on wireshark (3.6.5), with Nordic package 4.1.0 (python 3.10.4) The problem...
Good day I am wondering if you can help me.
For background information.
Network - NB-iot
Firmware - 1.3.1
Software - Serial LTE Modem
Hardware - nrf9160dk
...
