I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
There is a serial interface in the nRF SDK that makes it easy to serialize mesh data over serial
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hello,
I am want to read Analog value from LDR sensor. I am unable to find ADC Input pin in nrf52840 Dongle datasheet but I got it in nrf52840 chip datasheet (page -576...
Hello Devzone Community,
I have a question set regarding correct, best way or ways to configure nRF9160 GPIOs for high impedance. My hardware is a custom board but shares...
I have the nrfConnect task that builds my project in vscode.
I need to add a script to execute before the nrfConnect task.
I added a task to my tasks.json but the task...
Hi,
Could you please tell me which firmware is flashed onto the thingy91 by default (both for the nrf52840 and for the nrf9160) ? Where can I find the source code for these...
Hello,
We are experiencing a strange issue when quickly turning off/on the NRF52840 on our board. In order to check whether the MCU wakes up correctly, a test fw was set...
Hi all,
If a client has only one root certificate, the servers that clients can connect to are limited. I want to provision multiple root certificates first and use them...
Hi,
I'm using nRF52832 with BME688 Bosch sensor. I'm using APIs that are provided by Bosch, but I have to adapt them to nRF52832 microcontroller.
In particular, I'm not...
Hi,
I am using the MX25R64 NOR Flash chip on my own PCB with the nRF9160 package. With the help of this thread I have managed to get the NVS library to work with it. I...
hello all:
I'm using nRF52820, SDK 17.1.0, S113.
I made a BLE perpheral role, and it has two service, each service has two characteristic. like this:
When using nRF...
How do I remove nRF Connect SDK from Windows before re-installing?
And are there something that needs to be done, if you have used cmake and Visual Studio Code for other...
Hi,
I want to use in my project the saadc (I'm using segger embedded studio). So, I found that I have to add the driver file to the driver folder, and I have added the file...
im using nrf52840
with sdk 17
and segger ide
i recently discovered that the max count buffer is 16 bits meaning it has a limit of 65k bytes. im trying to receive 100k...
Hi @Torbjorn!
Hope you are doing good!
I tried using nrf52840/nrf52833 ble_app_blinky_c and ble_app_blinky for connectable coded PHY . But it only works for 1M_Phy . Although...
Hi there,
Our current understanding is that when building an application using NCS, the images of of MCUBoot and the application gets merged into merged.hex.
We however...
