Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi,
Is there any sample in nRF_Connect_SDK that implements RTC on nrf52840 SoC?
I need to implement RTC in my application, so is there any example reference for this...
Hello,
I am trying to set the `BT_SHELL_NUS` project up as a standalone repository. My requirements for this are as follows: I only want to commit application code to git...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We had to change the SDK version to 1.9.1 from...
I am trying to implement RSA signing into my application, I am planning to use the following example as a starting point but the sample, with no modification appears to not...
Hi there,
We are developing on the NRF5340, and have a question regarding the drive strength that can be set on a GPIO pin using the PIN_CNF register.
However we can not...
Hello,
i am using the nrf52810, ble_app_template example to read Accelerometer and gyro-meter data from ICM42605 sensor. so i have followed the i2c communication tutorial...
Hi there,
We are not able to find the reset due to brownout within the RESET->RESETREAS register? Is this the case? There are explanations of the brownout detection in the...
I'm trying to get DFU working with LPN on the 833. The sequence I follow is: (Erase board) Flash Soft Device Flash Bootloader (Using mesh, but don't want serial)
Flash Device...
Hi,
I'm trying to setup a very basic network based on the thread CLI example.
I have an nrf52840-dk as a router/commissioner and a custom device as a nrf52840 joiner...
This is the next step of the process getting the canbus working with nrf9160 and the aditional MKR CAN shield from arduino
previus part can be read here https://devzone...
Windows 10, Segger Embedded Studio V5.60a
nRF52833-DK (also nRF52840-DK, along with custom boards for each for later purpose)
SDK 17.1.0 S140
Hello, I'm trying to...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to change TX power of advertising but even though I have written the below...
Hi
We wan't use in our project some MODBUS sensors and I found, that Nordic Connect SDK (I use version 1.9.1) with Zephyr has support for MODBUS. I tried the samples (rtu...
Hi to All Colleagues:
New to Nordic and its development platform. Finished installing required tools using nRF Connect for Desktop v3.10.0. Attempting to use nRF Connect...
Hi,
I'm investigating possible improvements to our custom firmware update architecture. I'm curious as to whether it is possible to run the SoftDevice from a location in...
