Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
My name is Edward, I am trying to configure a net Thread with auto selection channel, do you have any example about this?
I have based my development on the simple_coap_server...
In the SDK ble_gatt_db.h file the ble_gatt_db_srv_t struct has a member misspelled as "charateristics" rather than characteristics. Was that done on purpose?
Hi,
I would like to resume the discussion made a few days ago in this post.
Is it possible to hide some BLE services until the connection is successful? I want only my...
I'm just starting... I have a little programing experience and knowledge of electronics
My project is controlling stepper motors over ZigBee using cell phone.
I have Samsung...
I have an application where I need to periodically write a few KB of data from my nRF to a host computer. Since TXD.MAXCNT tops out at 255 bytes, I'm trying to set up all...
Hi. I am trying to add a RTC to my ble project. I copied all the simple code from the RTC example, and set all the sdk_config.h settings to match.
As per usual millions...
Looking to permanently change UICR REGOUT0 to 5 for 3V3 on VDDOUT from dongle, to power a small Pulse Oximeter. Then using nRF Connect SDK and Zephyr, get Bluetooth GATT services...
Hi,
As a newbee :-)
Im trying on an nRf5340DK board. I use NRF-connect/Vusial Studio Code: I managed to use zephyr/samples/basic/bkinky example with a build in nrf3540dk_nrf5340_cpuapp...
I erased a board using a MAC (Monterey 12.1) and a Segger Version 11.0 Part-no 8.19.28
nrfjprog --masserase
After which I was no longer able to program, connect, or recover...
Hi,
I was wondering if it was possible to avoid JWT for the NRF9160 by establishing connection between an MQTT Bridge to Google Cloud. Our goal is to establish 24/7 connection...
Hi NRF folk,
when I build sample projects in VSCode (ncs1.8) it works only for some projects (zephyr_st_ble, zephyr_system_off,...). When I use any of the sensor project...
I am using nrf52840-DK and trying to get the Zigbee Switch working. This is just a plain zigbee switch with no bind to light. However, this set attribute during init results...
Hello,
I am trying to make an application with three dongles and one DK. This application consist on control the 4 LEDS of the DK, and each LED is controlled by one different...
I have encountered two issues while using the NRF PWM driver on the nRF52 DK, with or without SoftDevice S132, along with SDK v11.0.0
The first one is the use of the NRF_DRV_PWM_PIN_INVERTED...
