Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I have a JDY-16 BLE chip in AT command mode and are able to scan for a SoftRF device that has a Nordic UART service.
I can succesfully see the SoftRF device during a scan...
Hi All,
Currently I'm editing an example project using the NRF5 SDK in SES -- however, I'm not sure exactly how to best version a project or even export it to contain...
I am developing a product using SDK_17.1.0 and nRF52805. The basic function development has been completed.
I need the DTM firmware for RF test of the nRF52805 board, so...
Hi,
For my nRF52840 custom board, when I send data through app_usbd_cdc_acm_write() to the serial port from main.c , data are transferred without problem but
when I try...
Hello,
I just recently updated to Windows 11 and facing the issue(nrfutil is not working) after win11 update. Previously, It is worked on Win10. Do you have the working...
Hi.
nRF52-DK board use. (PCA10040)
* now system : bootloader + softdevice + Beacon application ->> working fine. good.
* new system : Swtiching ESB or Beacon
I would...
When I connected mqtt on nRF9160, I found a strange problem, which caused the device to freeze and become bricked. The location cause was found to appear in err = mqtt_connect...
Hello, we are semi-experienced with Nordic,
We are doing a DC power driver, during operation we do a NUS data send if we are connected and the NUS has started. When we get...
Hello,
I am trying to optimize GPS power consumption, and the fix time. The GPS search period is approximately 10 minutes, modem fw 1.3.1 and nRF SDK 1.7.0. We are also...
Hi Nordic，
is the encryption technology used in the software protocol or hardware inside 52833?
our customer want to know the if the encryption can export,thank you！
I baught new DK. Form last few days, I was testing sample programs for learning purpose. Suddenly, SDK stopped being detcected via USB port ? I could not diagnose the reason...
I got this error during development.
I think it is caused by the BLE device erasing the connection information with iOS,
I don't know under what circumstances the BLE...
Hi
I want to increase the number of leds in DTS file of peripheral-uart sample by using overlay file.
Is it possible to manipulate the aliases in DTS file by editing the...
I'm running in to the issue mentioned in the tile; " Only spi nodes accepted in /soc/spi@40023000/". I'm using nRF connect and built a driver for the TI ADS1291 analog front...
Hi, I read a couple of post that asked about the accuracy / tolerance of the internal REF, and the answers mention it's included in the gain error.
This made me wondering...
