Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello I'm using segger,i had my own project which its name is example_detector distance , i m trying to build this project by using make -j10 . all the files were compiled...
Hello !
I was trying to communicate with my Acsip chip, when I saw that the problem was coming from the nrf_serial_read() function. And here is my setup :
- I use the...
Hello, I want to understand why some example with the "nrf52832" crash. My project is about to scan BLE device to found tags.
To start, I have tried multiples examples from...
Hi,
As far as I understand it, TF-M stores symmetric keys unencrypted on flash in the nrf91, and then uses other means (like flash read protection and trustzone) to keep...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising, that's why I use the periodic_adv example coming with...
Hello,
I am using the vl53l5cx TOF sensor and implementing the ULD using zephyr. My setup is a bl654 board using zephyr on sdk 1.9.1. However I am running into an issue...
(replica as the previous post was archived by accident...)
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M....
Hello,
first of all i am a new user of NRF microcontrolers and embedded systems. I ve been searching on this forum for a simple PDM microphone example and although there...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
