Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi
Is there a possibility to read out the actual RX pointer of the DMA if the amount of chars is not reached?
Start Stop the RX is not really an option and I have no...
Hi everyone! I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice. The nrf go studio can not detect the nrf52832, but...
Hi,
I set sending of Ext. ADV at a periodicity of 500ms and scanning for 100% time by setting same interval and window configuration to 2.56 s.
But I observed that the...
Hi
I have a project to use HID mouse and keyboard at the same time, I have tried , but it really can't work well. I've read the similar question and you don't give the clearly...
Hi
I want to combine mouse and keyboard function together,and I had modify the example of hid mouse,show as below
but the question I meet is that the PC and phone reaction...
Hi,
I am developing an application (Peripheral Sensor device: Acceleration measurement), I have included the characteritsics for the measurement and I am trying to include...
I tried to enable the configuration of Thingy91 to use external sensors. I made following additions:
1. Added the following line to Asset_tracker_V2/K config file : rsource...
Hi,
is it possible for a central device to connect to a peripheral device directly (without using nrf_ble_scan_init( ), nrf_ble_scan_filter_set( ), nrf_ble_scan_filters_enable...
Hello,
I am trying to write some code that sets the BLE Tx power on the nRF52833 SoC.
I have based my code on the sample example code provided at C:\Zypher\v1.7.0\zephyr...
We're using the read authentication trigger to detect when a characteristic is being read, so we can update the value before a read. Is it possible to have a read with zero...
Hello,
at the beginning I want to state, that I have read all the tickets with similar issue, but still can't find any solution to my problem, that's why I'm creating...
Hi!
I was controling a little vibration motor with a mosfet which is activated by a nrf52840Dongle pin. I was using pin 0.17 and it worked pretty well, but now I am trying...
Dear reader
We want to use the floating point unit (FPU) in our project
We are building using the IAR compiler (8.5.x)
We'd like to use the hardware acceleration ...
Hi.
We are working on a project which uses nrF9160DK and nRF5340DK, which works fine on this last one. The problem is that when I tried building on the 9160 using nRF Connect...
