Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
Hello,
I am using the nRF52840 DK board and with Softdevice code nRF SDK 17.0.2. I am trying to write custom advertise data with custom type.
As you can see in the above...
Hi! Hope you are all doing well,
I'm having trouble making a project from scratch, I'm basically trying to filter bluetooth devices by manufacture code but I'm afraid that...
Hi All,
This has happened before so I know it's a handler error.
But this time I'm pretty sure my handle is not wrong, can help me?
in main.c =>
Best regards...
Hello After much research on this site trying to figure out how to use a PDM miocrophone, i finally have something that works. This is not a question so i hope it is allowed...
Hi,
Can you confirm the appropriate method to doing AFC correction for a GPS SNR test using the %XRFTEST command and then using the AFC correction result in the GPS SNR...
I use SPI to develop motion sensors KX022 and DW1000. The first digit of the received data is always 0xFF. If the first byte received is removed, it can be used normally....
I am trying BLE MESH light switch example with nRF5_SDK_for_Mesh_v5.0.0_src using nRF52833 DK. In the light switch example, server SDK is working fine and I can see the provisioning...
Hi All,
I am using Custom 128-bit UUID, My application need 3 Custom Services and 20 characteristics. But I need to make different Base for services and characteristic...
Hi,
I recently installed v1.9.0 SDK and while creating project from sample applications I am getting below error.
Attached is build logs from segger IDE.
Can anyone...
