Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Good evening,
Referring to the following page which lists IDEs that are supported by Nordic Nordic Supported IDEs
Please kindly let me know if the following toolchain...
Hello,
first I have to say that I'm new with nRF5340, Segger Embedded Studio and Cmake.
I have a working project with CMakeList.txt. So I include it into Segger Embedded...
Hi.
I am trying communication from nRF52832 to iPhone using ble.
I use main function which put in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart.
But,I...
Hello,
I have done the setup of Lsm5dsl with Nrf52832 DK board but I little bit confused about what hardware configuration is there so please guide me.
This is Code...
Hello Nordic great team,
We have a question please, we would like to configure our IOT device through the air, and the best way as we see in our use case, is to use the...
Hi there,
I tried to configure the openthread co-processor radio.
The build went well for my nRF52840 dongle, I managed to generate the RCP package image but when I install...
Hi!
I'm working with the nRF52833 in a Laird dev kit, the bl653_dvk and I cannot build a Hello World with mcuboot application in nrf sdk 1.7.0 or greater.
Although in...
Added the below lines to the peripheral_hr and I could see the logs without any trouble.
Same lines added to the central_and_peripheral_hr and I can see anything. What I...
Does someone have experience driving several slaves on a QSPI bus? Can we use a general IO pin for Chip Select (CS)? [Edtit] (I believe the nCS - QSPI pin described in the...
Hi,
I am trying to filter an iBeacon sample using a modified version of the central_hr_code.
Changes on the central_hr_code:
Added 128-bit UUID definition:
Added...
Hi,
I am developing a health wearable and want to store biosignal data into flash and then read at some point. I found that the reading process is relative slow as I tested...
Hi,ALL:
I use esb 2.4G liberary,and I found the same kind of produc build of nrf52840,it's radio current consumption is 1.2mA-1.3mA,how can it do it? My project is build...
Hi,
I have 2 nrf52840 DK boards advertising on coded PHY mode. Once connected the connection is updated (using sd_ble_gap_phy_update()) to use 2M mode. No problem in doing...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Please tell me about "ble_gap_conn_cfg_t :: event_length". The following explanation is written in the manual....
