hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
We are having connection problems with our nRF52832 based HID device only on Windows. I've attached packet captures taken with the nRF sniffer (nRF52 DK) and in Windows with...
I am using nRF52 DK and LIS3DH accelerometer.
LIS3DH configuration is as follows:
1. LIS3DH ODR set at 10Hz,
2. Low Power Mode (Low resolution),
3. Acceleration: 2g...
I am registering interrupts for many pins:
This only works for the first 8 pins, because from what I understand the GPIOTE peripheral is used and that has only 8 channels...
Hi
I am trying to program a nRF5340 device using programmer 3.0.0. But when I try to connect to the JTAG I get the below error.
using nRF Connect for Desktop v3.11.1 ...
Hello
SDK starts adverting when reset. I want to start adverting at the push of a button.
SDK version : 17.0.0
SWDevide : s112
When the button is pressed as above...
Hi everyone,
I want to send large data with https protocol.
I edited the https_client sample split the data and looped send() for sending the large data.
But when...
Hi all
I have an issue regarding central- peripheral connection.( using nRF52832)
In the past I developed a peripheral device using SDK 11.
In order to manufacture it...
Hello, I am doing a bachelor thesis using the nRF52 Development Kit to control a (RC ) car, and I am 3D-printing holders for extra peripherals. During the 3D-modeling and...
When I run nrfjprog --pinreset it says "Applying pin reset" but it has no effect on the connected nRF52832, it just continues running. Other nrfjprog operations like reading...
I am working on Apple Macbook Air with M1 silicon and I installed nRF command tools version 10.15.4macOS
When I open the toolchain manager , there is an error that shows...
Hello,
I am trying to get reliable log output using the Nordic Connect SDK (NCS) over RTT. When I use Minimal mode, the following config:
CONFIG_LOG_MODE_MINIMAL=y CONFIG_SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL...
Hi All,
Sorry for such a very basic question, but I've tried many things and combinations and cannot make this work.
I'm trying to discover BLE sensors using nrf_ble_scan_init...
Hello,
I am using the Zigbee NCP sample from the nrf Connect SDK and I would like to change the uart baudrate. How can I achieve this? I tried to find some configurations...
When I try to debug hci_pwr_ctrl in Zephyr/buletooth/sample using segger embedded studio, debug terminal don't have output of printk function, which based on nrf52840dk. ...
Hello All,
I am experiencing strange results when using the TWIM peripheral with and without using the debugger.
Setup :
Keil IDE for development and debugging ...
