I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi
Is there a possibility to read out the actual RX pointer of the DMA if the amount of chars is not reached?
Start Stop the RX is not really an option and I have no...
Hi everyone! I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice. The nrf go studio can not detect the nrf52832, but...
Hi,
I set sending of Ext. ADV at a periodicity of 500ms and scanning for 100% time by setting same interval and window configuration to 2.56 s.
But I observed that the...
Hi
I have a project to use HID mouse and keyboard at the same time, I have tried , but it really can't work well. I've read the similar question and you don't give the clearly...
Hi
I want to combine mouse and keyboard function together,and I had modify the example of hid mouse,show as below
but the question I meet is that the PC and phone reaction...
Hi,
I am developing an application (Peripheral Sensor device: Acceleration measurement), I have included the characteritsics for the measurement and I am trying to include...
I tried to enable the configuration of Thingy91 to use external sensors. I made following additions:
1. Added the following line to Asset_tracker_V2/K config file : rsource...
Hi,
is it possible for a central device to connect to a peripheral device directly (without using nrf_ble_scan_init( ), nrf_ble_scan_filter_set( ), nrf_ble_scan_filters_enable...
Hello,
I am trying to write some code that sets the BLE Tx power on the nRF52833 SoC.
I have based my code on the sample example code provided at C:\Zypher\v1.7.0\zephyr...
We're using the read authentication trigger to detect when a characteristic is being read, so we can update the value before a read. Is it possible to have a read with zero...
Hello,
at the beginning I want to state, that I have read all the tickets with similar issue, but still can't find any solution to my problem, that's why I'm creating...
Hi!
I was controling a little vibration motor with a mosfet which is activated by a nrf52840Dongle pin. I was using pin 0.17 and it worked pretty well, but now I am trying...
Dear reader
We want to use the floating point unit (FPU) in our project
We are building using the IAR compiler (8.5.x)
We'd like to use the hardware acceleration ...
Hi.
We are working on a project which uses nrF9160DK and nRF5340DK, which works fine on this last one. The problem is that when I tried building on the 9160 using nRF Connect...
