Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I have a problem with nRF24L01 working as a PTX. Not very often but occasionally now and then it doesn't transmit any messages and requires removal of power before transmission...
Howdy all,
I have noticed that there are some limitations regarding the replay cache in BLE mesh devices.
Environment:
1. nrf52840
2. MESH_SDK V5.00
I have developed...
My device is connected all the time to a server with a persistent socket. I’m using eDRX power save modes so current will stay low in my battery operated product. During operation...
Hello, I'm experiencing an issue with talking to our mesh server after an IV update occurs. After a fresh provisioning the unit talks fine, however, one of our units has an...
I use nRF Connect for Desktop download the NCS v1.9.1, and i use SES open "C:\ncs\v1.9.1\nrf\samples\nrf9160\location" expample, but when i want build this solution or build...
Hello,
Are there any steps or documentation specific to nRF5340 to perform DFU over BLE and store the image into external flash and on the next boot it should get executed...
Hi guys,
As long as I know the Arduino Nano BLE 33 is built upon the nRF52840 microcontroller, so I am wondering now is it possible to use the source code from Nordic SDK...
Hi,
I am changing some code in the bootloader and would like to see some logs inside a specific function. The problem is that when I place the call for NRF_LOG_DEBUG() before...
Hi,
as am following below link for DFU-OTA . i was able to perform it. https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t...
Hello, this is a follow up on this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/84834/protecting-the-battery-via-sleep-mode
Our goal is to switch off the device ...
Hi,
I'm trying to understand which of the BT L2CAP modes are supported for a BT LE Controller. BT Core 5.3 supports these modes of operation:
Basic L2CAP Mode
Flow...
Hi.
Is it possible to add SPI or QSPI cleanup once mcuboot is done?
I've checked nrf_cleanup.c , but it seems that (Q)SPI is not turned off, which increases the power...
Hello,
I'm using nRF52833 MCU board for my project, I have to do power optimization to my project(Device).
In my device two sensors are there, and boost regulator and...
Hi, I have made a project that is based upon the aws_iot sample. The version of SDK and toolchain is 1.7.1. Now I have tried to upgrade to version 1.9.1. But then I get compile...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
