dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, we have a thread that essentially is running a loop and we want that thread to be running for all the lifecycle of the app. If for whatever reason that thread died...
Hi Team,
I am using Open Thread networking protocols in my projects to communicate with the devices .I have seen while trying to changed some parameters over the network...
I am unable to do a FOTA with the SLM application on a nRF9160. When I try to do a FOTA with the command below, I get a 404 even though I know the URL exists (real host name...
Hello,
I have been working with custom nrf52832 board to develop firmware for my product. I have been trying to compile the example secure bootloader from the SDK v15.3...
Hello, I am developing a uart communication between the nrf52833 and the nrf9160. I found some examples but I don't want to use the HCI layer, I prefer to use the NUS service...
We have an application that wakes-up every N minutes and listen to devices in a ble mesh then performs many other actions. In order to save battery, we would like to power...
Hello
OS :- Linux
Hardware version :- BC805M
SW :- Segger embeded studio
I am using nrf52805. I am test it with ble_app_uart. It advertisement continuously and shown...
Hello,
I'm trying to transfer data to an L2CAP CoC on a nRF52832 from iOS and Android devices. I've configured the MTU and MPS so that the SDU fits in a single packet with...
I'm using BLE Mesh Sensor example that Client & Sever communication data each other.
Because I'm implementing one by one communication data that client > sever > client...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to add a custom UUID in the advertisement packet and scan for the custom UUID in the central device to...
Hi,
Our firmware currently only support full modem update, and I would like to perform a full modem firmware update from 1.2.0 to 1.2.7. According to the reply from https...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
I am getting a softdevice hard fault occasionally, on fully enclosed devices with no debugger port access.
Where can I find info on potential causes of this fault?
nrf51822...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
