dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello, All;
Using your nRF9160 chip to develop, there are some questions when using the network and positioning, Hope to get your answer:
1. Can LTE work at the same time...
Hello,
I have two projects, one for the application core (modified BLE Peripheral sample) and the second is for the network core (modified HCI_RPMsg sample). I am currently...
Hi all:
condition:
SDK14.2
PCA10040
example: ble_app_uart_c
I have a central device ,it need to scan RSSI value of peripheral.
If the RSSI is more than threshold...
Hello,
we were using the HRS example as a starting point and modified it for our application. Everything works fine, we can see our custom characteristics, control our device...
Is it possible, without having to join ZOI, to recompile the Zigbee ZBOSS NCP Host for the Raspberry Pi?
The NRF Connect SDK documentation under ZBOSS NCP Host states :...
Hello,
we have an custom made board with a module from raytec MDBT42q.
Our application based on the nus example.
On port 0.7 we have a led.
It seems, that there is...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
I want to add a simple GPIO pin that act as output pin, in the peripheral_uart example .
in main.c
#include <drivers/gpio.h>
//#define GPIO0_LABEL DT_PROP...
I'm using ble_app_uart_c project in nRF5 SDK 17.1 with SES.
I got 2 different devices, one is ARC EM9D AIoT DK (as Peripheral) and another is nRF52840(as Central).
I was...
Hi,
nRF9160 with SLM NCS v1.9.1 fails to attach after 7th RESET (by RESET pin) & attach without power cycle.
There is not any ERROR state reported by modem, modem fails...
Hi All,
I am using s112_nrf52_7.2.0_softdevice with nRF5_ SDK_17.1.0 and Segger Embedded studio for nRF52805.
My application code is successfully patched for nRF52805...
Hi,
I'm using the default software to check the acceleration values when there is a movement in the Thingy:91 on the LTE Monitor terminal.
The document says that this...
Hi,
I want to test of MQTT communication with nb-IOT network before going for development.
For that I have updated pre-built firmware on development board using nRF...
