dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hey,
I'm trying to follow a few guides on sniffing BLE connections (eg https://hackaday.com/2021/03/23/a-crash-course-on-sniffing-bluetooth-low-energy/ ) with an NRF52...
I'm trying to get my nrf9160dk board up and running with the nrfcloud service. However, when I input the SIM ICCID and PUK, the nrfcloud site starts it's "working" process...
Good day
After flashing a sample to my thingy 91 I seem to have lost the Jlink connection. All im picking up is the UART via nRF connect Programmer. Is there a Bin file...
Hello Sir/Mam;
I am new in nordic environment so i need your valuable guidance . i want to read a sensor data using Uart . I have successfully do same thing on Arduino board...
Hi,
I had previously asked about SPI interfacing of the RFID card reader and I was successful in creating a custom application using connect SDK 1.5.1.
But according to...
I currently have an application with B0->SPM->MCUBOOT->APP and am looking for an example of how to upgrade MCUBOOT itself over the air from a file downloaded from some server...
We're using a nRF52DK and the Nordic-Programmer-App to flash our firmware on our custom boards. After upgrading to Programmer v2.3.3 I'm getting the Error-Message "Part of...
Hi,
I am able to successfully build and flash applications from the CLI.
When setting up the nRF Connect VS Code extension, I run into an issue where it can't seem to...
Hello, I am trying to use the spi_flash sample project with a laird bl654 dvk. When I run the project however, dev->state->init_res = 19 and will not run for me. It recognizes...
Hi,
I have been trying for several days to modify the ble_app_uart project on the peripheral side to use the BLE Long Range, unsuccessfully. I use the NRF52833-DK with...
Hello, sir.
I want to use the i2c bit bagging method, thus I used the DeviceDownloadnRF5 SDK 17.1.0 ddde560nRF5 SDK 17.1.0 ddde560componentsdrivers nRF5 SDK 17.1.0 ddde560componentsdrivers...
I want to use the Zephyr Shell with my own transport layer. Since the only connection I will have to the modem is over SPI, I want to have the SPI read/writes handled with...
I am using sdk 17.1.0 .I am getting error while using bsp_buttons_is_pressed function in main although i have included file bsp.h ,bsp_btn_ble.h, boards.h. The error is Error...
Hello,
I've been developing an application with nRF52840 and I've been reviewing the appropriate SDK to start with. I see Nordic recommends starting with nRF Connect SDK...
