I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello,
we have a zephyr application on nRF52832 DK with nRF Connect for vscode
Before we added DFU support, we had a power consumption of 28 uA
After adding DFU support...
3 months ago Nordic stated the following
The S140 version 6.0.0 SoftDevice does not have full support for S=2 (500 kbps). The application cannot select S=2, so all packets...
Hi Nordic guys,
I'm developing with nrf5340, and meet some problem with writing external flash - nrf qspi flash.
I found it sometime failed in 'flash_area_write' and return...
Hi,
I'm using SDK17.02 on nRF52810, when my application have an error, it will log "fatal error" but never reset system. BTW, I'm not debugging and just watching the RTT...
Hi
I want to update the ble advertising data in my program. In nrf5340 the bt_le_adv_start() command should run only once in the main program.
Is it possible to change...
I 'm developing a program (C# ) on PC for the nRF52840 dongle (pca10059) that is a RSSI scanner.
Scanning different BLE channels in the environment. The program is much...
Hi Sir,
We plan to test the WebUSB example under the below path:
/ncs/1.8.0/zephyr/samples/subsys/usb/webusb HW: nRF52840-DK When we compile, program and connect to the...
I bumped into some compilation errors regarding PRS box4, when I tried to remove UART from an example.
I saw that PRS is "Peripheral Resource Sharing", but it looks like...
I am working on nRF Connect SDK 3,9.3 version. One day a dailog to update appeared. I clicked to update while SES was also opened and I was working on a project. Suddenly...
Hi,
I am working on a firmware and have added custom services to HRS example on SDK 17. I want to know if its possible to add BLE multiperipheral capability to my device...
I don't have enough pins to dedicate a SPI bus to the nRF21540.
In the webinar I attended I believe I heard that the SPI bus is not supported by the current SDK anyway,...
Hello everyone,
This was discussed before, elsewhere ( link) , however, it is meant for the "nRF51422 chip " and I need to resolve some other points too ...
it is necessary...
Hi,
I am working on the sample DFU OTA project as recommended below,
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu?CommentId=3cb5df69...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
