I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello,
I am doing BLE advertising on the nRF52833 and using nRF5 SK 17.0.2. I cannot set TX power above +4dbm from sd_ble_gap_tx_power_set(). I have checked in nrf_gap.h...
The "Flash" and "Erase and flash" actions wer working fine a few days ago，now it only execute "west build".
I pressed "Flash" or "Erase and flash", it just executed "west...
OK, I'm using Visual Studio Code with the nRF Connect extension. I'm playing around with some simple BLE code (trying to set up DIS and then a custom service). All of a sudden...
Hi Sir/Miss,
In original project, I use nRF52810. But, it's not enough flash in our customer adding requirements.
Therefore, I want to migrate project from nrf52810...
Hi,
I'm new on NRF connect with visual studio (I have programmed nordic devices before, nrf51), right now I am working with a nrf5340.
So far I have created a blinky...
Hello Everyone,
When I debug the GPIO interrupt of nrf5340, the edge trigger can be normal, but it will be triggered all the time when the level is triggered. Does anyone...
Hello,
I am trying to implement a system where the board waits for a character to be pushed to the RX buffer before reading it. The character would be sent by another microcontroller...
Users can often help each other and not rely on your staff.
I am trying to join a sample/matter_light_bulb sample to a newly formed Matter network.
The problem I describe...
Hello,
I am figuring out the fstorage functionality and I'm running basic example flash_fstorage from SDK 17.1.0 on my nRF52-DK. And I got the issues just on start.
At...
Hello,
I'm trying to control a motor via a mosfet. Setting the mosfet on/off with pin assignment works great, however pwm at any value other than 0 or max burn out the mosfet...
Hello,
We have a design that includes both the nRF52840 and the nRF9160. We are doing custom antenna designs in a miniaturized form factor and would like to specify required...
Hi
We are verifying the encrypt value and MIC value using a crypto tool.
The result is different depending on the setting of the packet S0 field.
If the S0 field is...
Hi,
I have been working on a setup where I connect a sensor (TI ADS1299) to the nRF5340-DK 2.0.0 using an SPI connection and transmit the recorded data using BLE. I have...
