Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I am trying to build the 'at_client' nRF9160DK sample app on a Mac and getting the following error:
CMake Error at /opt/nordic/ncs/v2.0.0/zephyr/cmake/modules/zephyr_module...
I am having the same problem as in
Case ID: 244142
devzone.nordicsemi.com/.../nrf52840_dk-spi-configuration
I am using nRF5340.
The problem I'm facing is that...
I use this code " node cli create-and-provision-device-cert"
But I am using nrf9160 ,so therefore I change this code to "node cli create-and-provision-device-cert --dk ...
This should be so easy, but it isn't. I started with the Dev Academy Lesson 6 I2C example. I wired up a little board with an I2C eeprom, created an overlay file to map the...
I have an OpenThread application that worked on NCS v1.9.1 and after updating to NCS v2.0.0 (nothing in the source code or kconfig was changed), the application fails to build...
Hello,
i found a few articels about it but none of them where helpfull for me.
I just want to use my nRF51822 Module from Raytac without an external 32khz oszillator....
I was having an issue where reading from SPI inside a timer handler always yielded 0xFF instead of the actual values. I tried to reproduce the issue with a simple test program...
I'm trying to do a firmware update over BLE.
Here's what I did: - I created a new application from sample "smp_svr" because I think that is where I can see how to do firmware...
Can you please explain how the %XCOUNTRYDATA command can speed up network selection in a new location? Does the modem perform a general scan on all bands to determine the...
Hi everyone,
I'm wondering on which plateform / app and how is it possible to read and retrieve the data sent from a nRF52833 Slave to a Mobile Phone (Master) ?
We have...
I'm running on Windows 10 and am trying to connect to my BMD-350 development board with an NRF52832.
I've also attempted to execute this with Python 3.9 and 3.8 (both installed...
I'm using SDK17.1 and pca10056 DK board. I want to use app_sched_event_put for a very simple purpose. I start a one second clock whose timeout handler increments a static...
Hi
I have configured my project to have a Modbus RTU slave on UART1. When I poll the dev kit, using Modscan, I get frame length errors. I have checked baud rate and parity...
I am trying to figure out why my application is generating a hard fault. The hardware platform is nRF52832 and SDK is 17.1.0
In my experience, the generic Cortex M3 processor...
Hi,
My customer use nRF52840 with nRF5 SDK 15.0.0.
They have come up against the difficulty that uart RX pin instability.
I have searched the DevZone and it's advised...
