S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
Hi
I still have a number of devices that are based on nRF24E1. From time to time the chips need a change in firmware. Since the last time I updated them, my PC has crashed...
Hi support team
I have been modifying the throughput example (nRF5 SDK v17) to connect the receiving unit (AMT client) to more than one device. I am running this on the...
Good day
I have Ubuntu 20.04.3 LTS installed on my laptop + fresh installation ( ~/.nrfconnect-apps was cleared and app reinstalled ) of nRF Connect 3.9.1
I use Bluetooth...
Hello!
My steps:
1 - Full working dfu over ble on nrf52840-dk + nrfutil + nrf52840 Dongle
2 - Change transport BLE -> ANT + nrfutil + ANT USB Stick 2, ANT USB(two different...
I am new in nrf52832 field i am trying to send some customized data(scan response) in ibeacon format of advertising. suggest me some ways or code to do the same
Thankyou...
Hi,
I have a custom EVB from Taiyo (EYSPBNZUA), https://www.yuden.co.jp/jp/product/category/module/img/TY_BLE_EYSPBNZUA_DataReport_V1_0_20201019E.pdf
When I press the...
Using above strategy for frequency measurement. Frequency source connected with one gpio pin.
Only GPIOTE PPI Timer modules are involved
HFXO is in use full time through...
