Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I'm using nRF52805 with LIS2DW, accelerometer.
LIS2DW is controlled by I2C protocol. but I do not use nrf I2C driver. I am using two GPIO port emulating I2C. It works...
Hi,
Regarding QSPI, could I use the QSPI feature to fetch stored sensor data directly from the flash and send it via Bluetooth module, or is it only to increase the application...
Hi,
I have two nRF52833 and i want to make one tx and one rx (with an antenna array) for direction finding (AOA mode).
I have already compile the project called "direction_finding_connectionless_tx...
Hi I'm developing an application using SoC nRF52840 and I need to use load cells to measure some weights. A lot of existing solutions use the HX711 chip to amplify the differential...
Is there any peripheral sample for OOB legacy pairing? I'd like to know how to encrypt with temporary key( TK). I checked the ble_hids_keyboard_pair_nfc sample in the SDK...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
Hello,
As we are close to production of our new device, i would like to know what are the possible ways of performing OTA DFU in thread network from Thread Border Router...
I have interfaced two ESP32's with ESP-NOW protocol in which one esp32#1 sends the data to the other esp32#2. I am able to send the data from esp32#1 and receive that data...
The nrfjprog tool only returns data up to 0x10001000. After that it's all zeros.
nrfjprog -f nrf52 --recover
nrfjprog -f nrf52 --readuicr uicr.bin
If I read an individual...
Hi,
I want to use the LIS2DH sensor to any motion interrupt on int2. It seem that it's implemented by the driver so I started with the code found in this issue ( https...
I'm trying to disable proxy visibility of mesh node after its been provisioned by calling (from APP timer's context) proxy_stop() function. Though i'm getting NRF_FAULT_ID_SD_ASSERT...
Hi,
I am using nrf51822 chip for BLE application. In my circuit, I have used circuit supervisory components which is resetting the MCU whenever voltage level goes below...
Hello,
I have found out that we have shipped one product where NRF_CLOCK_LF_SRC_SYNTH was used together with the SoftDevice S132. I think at the time when it was implemented...
Hai team,
In my application , I am using nrf52832 , application took 26 microamps in runtime [peripheral - I2c] ,acclerometer and ble advertisements],here i need to put...
