I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
We are trying to integrate the STEVAL_MODEM_BG96 chip into the NRF52840 for rapid prototyping. Trying to interface nrf52840 with the STEVAL-
STMODLTE chip via UART. Connecting...
I used to have a dts file for sdk52dk_nrf52832 containing gpio1 references:
rts: rts_pin{
status = "okay";
gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
label = "TS pin...
There was a question when doing the multi-channel test of ANT. The SDK is 17.1, and the example is (ant / ant_ multi_ channels)，Encountered the following problems：
1、Example...
I have
nRf52840 DK - 1 - Mesh Serail example nRF52840 Dongle - 2 - Mesh Light Switch Server example.
I used the steps given in the infocenter to provision and configure...
Hi,
Is it possible to be in connected mode (exchanging data) and also advertise data packet (on primary channels) between two BLE devices (so, in both the modes) ? Is there...
When using nrfjprog over an IP connection, `--ids` never returns a value. This is frustrating as the Zephyr nrfjprog runner uses this command to determine if there is a board...
Hello !
In latest errata, https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_3_Errata_v1.1.pdf is not so clear all details of this anomaly
[254] RADIO: External PAs, FEMs...
My laptop is running the latest macOS 12.4. It is a 2021 Macbook 14" with M1 Max.
I updated nRF Connect For Desktop and Toolchain Manager to the latest versions, then I...
I am trying to port a timer over to the nrfx_rtc driver and I can't seem to get it to start counting. I'm sure I'm missing something small, but I'm not seeing it. SDK 17,...
Hi,
I have a medical device where my mother board has a NRF52840 chip which communicates with a Android Tablet through blue-tooth. We find it gets connected with few tablets...
Hi, I am working the Zigbee in nrf connect SDK 1.9.1 I am running light_bulb, switch and coordinator examples
I want to change the panid , Short id, via proj.conf
how...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
Hi,
I am using an nrf5340 with nrf connect sdk v1.9.1. I need to calculate the duration of an event with nanosecond precision, so I am using an nrfx_timer at a frequency...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
When I run TX tests with the AT%XRFTEST command, I can start the TX test without any problem but then the modem stops responding to AT commands. For example, if I send
...
