Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hello
We want to use the Gazell protocol into an Arduino IDE based firmware project.
Therefore I would like to know if you have any advice, documentation, examples, etc...
Hi
What is the max size of RAM and Flash for APP?I looked in the partitions.yml of a sample，I found that there is many region for different use，I don't know which region...
Hello,
Please share any working document to enable UART2 for external communication. I gone through many documents and forum and many setting in prj.conf but still no results...
I have 2 devices in the same SPI bus defined in my devicetree. let's call them MAX30005_1 and MAX30005_2.
When the drivers initialize, they read a register of the device...
Hi Folks,
As per bluetooth spececification(4.4.2.2.1) advertising interval has addition of advDelay in range of 0-10ms. In my example,
1. device advertise beacon (sd_ble_gap_adv_start...
Development Kit: NRF52840
IDE: Segger Embedded Studios
I'm trying to use the nrf_drv_twi driver in my project. I've included the .c file in my nFR_Drivers folder. My...
Hello,
I am using the nRF52840 DK board and with Softdevice code nRF SDK 17.0.2. I am trying to write custom advertise data with custom type.
As you can see in the above...
Hi! Hope you are all doing well,
I'm having trouble making a project from scratch, I'm basically trying to filter bluetooth devices by manufacture code but I'm afraid that...
Hi All,
This has happened before so I know it's a handler error.
But this time I'm pretty sure my handle is not wrong, can help me?
in main.c =>
Best regards...
Hello After much research on this site trying to figure out how to use a PDM miocrophone, i finally have something that works. This is not a question so i hope it is allowed...
Hi,
Can you confirm the appropriate method to doing AFC correction for a GPS SNR test using the %XRFTEST command and then using the AFC correction result in the GPS SNR...
I use SPI to develop motion sensors KX022 and DW1000. The first digit of the received data is always 0xFF. If the first byte received is removed, it can be used normally....
I am trying BLE MESH light switch example with nRF5_SDK_for_Mesh_v5.0.0_src using nRF52833 DK. In the light switch example, server SDK is working fine and I can see the provisioning...
Hi All,
I am using Custom 128-bit UUID, My application need 3 Custom Services and 20 characteristics. But I need to make different Base for services and characteristic...
Hi,
I recently installed v1.9.0 SDK and while creating project from sample applications I am getting below error.
Attached is build logs from segger IDE.
Can anyone...
