I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am new to Zephyr and I have been trying to get hold of a tutorial or a sample app that would indicate how I can use the UART on the nRF52832 for communications with another...
Hi,
I'm wrapping up a project which uses an nRF5340 as both a Bluetooth peripheral to advertise etc and also as a Bluetooth central to scan for devices (not both at the...
I recently started development on NRF52833 for one of my projects. I use segger embedded studio with the " ble_app_uart " example. As I mentioned I'm using nrf52833 DK so...
I want to recover DFU over BLE upon a dropped connection while in the middle of an update.
I have my own software that I've cooked up to program from another NRF52 chip...
Hi,
I see you have what appears to be a working implementation of OOB/NFC pairing over iOS here ( https://github.com/NordicSemiconductor/IOS-Nordic-Thingy ), which doesn...
Hi,
Here is my previous ticket.
https://devzone.nordicsemi.com/f/nordic-q-a/83856/channel-interference-at-nrf52840
I haven't had response tho that's why I made a ticket...
Hello! We have an application that I need to implement Tensorflow Lite. We started with the Arduino Nano 33 BLE Sense board, which had a TFL library on it. After using it...
Hi,
For 52820-QDAA, what load impedance is preferred seen into the matching network? I mean the total load impedance of C3, L1, C4, L2, RF trace and antenna.
Since our...
In our application, we've enabled full modem firmware update, which requires us to enable CONFIG_NORDIC_SECURITY_BACKEND. When we also enable memfault, this compile time pre...
I am build an application with features : When I not used nRF it imediately in sleep mode and be wake up by BLE events to send some text, and return to sleep mode ( the reson...
Hello there, Thanks for writing an application layer for SGTL5000. https://github.com/NordicPlayground/nRF52-teensy-sgtl5000-audio
I've configured the SGTL5000 to source...
We have a simple coin battery powered BLE device with a Laird BL652 module which has an nRF52832 chipset.
We have three buttons and set it up as low power as possible...
Hi, I downloaded a project from Git. I tried to open in SES using nRF Connect SDK. During the initial Cmake, the error occurs as shown in attached image.
Hello,
Our aim is to install "pc-ble-driver-js" and use the connectivity board for the serialization process.
We are following this link to get this working https://github...
Hi!
In previous versions of the SLM it was possible to provide a hex datatype to the XUDPSEND command to send blobs of data over UDP, without having to worry about a stray...
