I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello!
First of all, thank you for your support.
I'm starting to develop firmware for Nordic chips (I'm a complete newbie). I have been able to compile and download examples...
Hello everybody,
I'm trying to develop simple time synchronization system upon mesh time model, but after sending bt_mesh_time_cli_time_set, first of all my time_update_cb...
NRF52840, SDK, nrf5-sdk-17.
This could be a misunderstanding of how the dual bank update works, however I am finding that after an OTA, Bank0 contains the new fw image but...
I have an SPI sensor that benefits from having a precise clock source, and has a muxed pin that can have a clock source.
The peripheral states that this pin can handle frequencies...
Hi,
We have implemented the DFU Trigger Library on nRF52840 from nRF SDK 15.3 on Application FW. Application is flashed on the device along with Secure Bootloader using...
Hello Nordic team,
I come to you because I face a strange issue during developing a simple feature using PWM.
For a product, I need to make an LED blink smoothly 3 times...
I have a NRF52840 Devkit and also subsequent NRF52840 boards, and I was wondering if there's any WiFi support on them now. I'm aware that it's possible to use any WiFi module...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I'm building a nrfmicro bluetooth keyboard controller which uses an ebyte E73-2G4M08S1C nrf52840. My programmer is cmsis dap link. Openocd verson is 0.11.0.
I built two...
Hi All,
I'm new to this wireless field. Is there any impact on power consumption based on RSSI level.
As I understand due bad RSSI there will be retries in communication...
I working on Asset_tracker_v2. After going hrough the code, I estimated the work flow to be as:
1. When either Passive or Active state is intialized, the Sample Timer is...
Hi there,
I am running into this error Update CTE params...failed (err -134) while running the direction_finding_connectionless_tx
The output logs are
can I get more...
Hello,
In the product specification for the npm1100 there is an optional battery monitoring circuit schematic on page 39. I'm having trouble understanding why there are...
As described in the topic, I wrote my own bootloader (located at 0x70000). When I restart from the app (located at 0x26000) and enter the bootloader, NRF_ Log doesn't work...
