I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I use nrf connect sdk 1.9.0, to run periodic_adv and periodic_sync example.
The adv side sends this data: mfg_data[] = { 0xff, 0xff, 0x00 };
But in sync side in scan_recv...
Hi,
My mesh project is occasionally suffering some dropped messages and after probing around I found this on one of the nodes.
I have four nodes and one gateway running...
Hi,
In nrf52840 dongle, I use nrf_crypto_ecdsa_sign function to sign.
Everything is fine in when building, but when testing the real world data, it’ll will show error...
I use 52820 to do ble_usb+esb project, but I have encountered problems when adding USB. I have added USBD_HID_COMPOSIT in the project of \ examples \ peripheral \ usbd_ble_uart...
Dear community
I am developing an autarkic embedded system where I harvest energy from a thermoelectrical generator. It is a simple application, I need to acquire the open...
Hello,
NCS1.8.0 Windows10 X64;
i test v1.8.0\nrf\samples\bluetooth\direct_test_mode, and i want to use nrf21540 model.
i've set CONFIG_NRF21540_FEM=y and do Project...
nrfjprog restarts nrf5340DK debugger
We are running a container environment in Ubuntu 20.04 on WSL2 and the USB ports are frwarded using usbipd
When trying to flash (or...
Hi,
I have been playing around with the nRF9160 DK trying to get it reading a range of sensors, so far with success, however I have found an issue which has stumped me...
We use nRF9160 on our own board. The firmware "Serial lte modem" is installed on the chip with connection to an external MCU. We connect to the broker through the MQTT command...
Hi,
I'm trying to compile Zigbee examples nRF5-SDK-for-Thread-and-Zigbee in Keil but faced some errors.
This is the error I got. This is the exact location of the project...
Hello,
I'm designing a device based on nRF52840 SoC that receives a configuration (set of 50 parameters) from an app which downloads the configuration in JSON format from...
Hi, I tried to run an adc example ( https://github.com/haakonsh/NCS_SAADC_example/tree/master . ) for nrf5340 in another post ( how-to-configure-the-dma-in-adc-and-how-to...
Hej!
Upgrading from SDK16.0.0 to SDK17.1.0, concerning sdk_config.h in my application: I worry that some new options could have been introduced while some old ones might...
Dear support,
I tried to follow the video here for adding service to https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6 ,
Read and notification works fine...
I think I may have found errata. Using the combination in the title I can enable output, verified at the pin using OUTSET. Once the softdevice is enabled the same command...
