I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hello
I'm using nRF5340 DK with nRF Connect SDK 1.5.0 and SES IDE and I want to change the PHYs and TX power of the peripheral_uart sample ( v1.5.0\nrf\samples\bluetooth...
Hi,
Based on peripheral uart sample code on nRFConnect SDK 1.8, I'm developing a custom BLE application under nRF5340 using VSCODE though nrfConnect extension.
In order...
I tried to program this example developer.nordicsemi.com/.../README.html onto the nRF5340 network core, following the instruction from here devzone.nordicsemi.com/.../ncs...
Hi,
I am new here. I have a very basic question, maybe bordering on Dumb.. but couldn't see the answer in previous questions.
My board will normally be working on AC power...
Hello,
I'd like to remove the "configurations" in Segger Studio and the associated extra directory level; I consider them counter productive.
So how can I get rid of those...
Dear Sir.
A timer is defined for 1 hz,
Every 3 minutes or so we drive the buzzer with different pulses ( see code attached )
We are using the PWM to drive a buzzer...
error repported segger
39 minutes ago
Online lm
47 pts.
Hello, i'm trying to flash a code in my module nrf52805 thx to my Dk nrf52840. i have this error I...
Hi team,
I'm streaming the sensor data through USB (using hterm) every 2.5ms.
i have configures USB as CDC and using virtual COM port.
In each iteration, i transfer...
i have nrf52832 using nrf sdk version_17 and s132.
I have application for logging
i have followed steps:
1). intially device in sleep mode
current: 0.35 micro Amp...
Hi,
I am working at a project that was abandoned by a guy that worked on my position. I have to fix some issues and add some features. I'm using SDK 17.0.2, my IDE is VSCodium...
Dear all,
I am now using two nrf52840DK and nrf connect sdk v1.7.1,and I want to send packet using llpm mode between two devices,one is receiver and the other is sender...
I need a battery-powered programmable device to communicate via Bluetooth to a headset, and communicate with another device via serial (TXD/RXD) interface. Performance requirements...
Hello,
I am writing a single byte value to a cypress module using write with response (BLE_GATT_OP_WRITE_REQ). For some reason the peripheral will receive the value but...
Hi!
I am trying to develop a way for a Bluetooth Central and Bluetooth Peripheral using Secure Connections (security mode 1 level 2 if I'm not mistaken) using a static...
