I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
I'm using Ant sdh,I want to make system enter sleep,how to disable nrf_sdh_ant?
I usd this function to enable sdh,but can't disable sdh to enter sleep,how to use?
static...
Hello,
1.Which platform is recommended for developing Bluetooth mesh, nrf5-sdk-for-mesh or NCS?
2.What is the difference between nrf5-sdk-for-mesh and NCS?
3.What is...
Hello Devzone Community,
I am facing a run time, peripheral or sensor initialization error in a Zephyr based app, built using sdk-nrf v1.6.1, and its corresponding Zephyr...
My Zephyr based application is buildable and working fine. I followed this tutorial, trying to enable bluetooth OTA for my app: Add DFU support to your application - Software...
Programmer 2.0 is broken in nRF Connect for Desktop v3.8.0
Very often it does not detect connected devices, even if I disconnect and reconnect the nRF9160DK which is also...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
I used \ncs\v1.8.0\bootloader\mcuboot\samples\zephyr\hello-world as a starting...
Hello,
We have a battery-powered product that currently uses the NRF52832. It is a very low power space-constrained application, so we always evaluate any potential current...
Hello,
I have set my softdevice s132v3 with SDK12.2 and nrf52832 to use connection event length extension and data length extende with connection parameters as shown below...
Hello,
I'm currently trying to implement a simple scenario: Using the nRF52840_Dongle, provide LOG output to the console.
This is the main program:
This is the usb_console...
Two Factor Authentification is enabled for my primary account (I had to create a second one to ask question).
Something has gone wrong with setting up two factor authentification...
I wanted to implement a time sync feature on nRF-52840 DK. I took a reference from this example, but there were certain things unclear to me.
Can somebody explain to me...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
