I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Is there any peripheral sample for OOB legacy pairing? I'd like to know how to encrypt with temporary key( TK). I checked the ble_hids_keyboard_pair_nfc sample in the SDK...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
Hello,
As we are close to production of our new device, i would like to know what are the possible ways of performing OTA DFU in thread network from Thread Border Router...
I have interfaced two ESP32's with ESP-NOW protocol in which one esp32#1 sends the data to the other esp32#2. I am able to send the data from esp32#1 and receive that data...
The nrfjprog tool only returns data up to 0x10001000. After that it's all zeros.
nrfjprog -f nrf52 --recover
nrfjprog -f nrf52 --readuicr uicr.bin
If I read an individual...
Hi,
I want to use the LIS2DH sensor to any motion interrupt on int2. It seem that it's implemented by the driver so I started with the code found in this issue ( https...
I'm trying to disable proxy visibility of mesh node after its been provisioned by calling (from APP timer's context) proxy_stop() function. Though i'm getting NRF_FAULT_ID_SD_ASSERT...
Hi,
I am using nrf51822 chip for BLE application. In my circuit, I have used circuit supervisory components which is resetting the MCU whenever voltage level goes below...
Hello,
I have found out that we have shipped one product where NRF_CLOCK_LF_SRC_SYNTH was used together with the SoftDevice S132. I think at the time when it was implemented...
Hai team,
In my application , I am using nrf52832 , application took 26 microamps in runtime [peripheral - I2c] ,acclerometer and ble advertisements],here i need to put...
Hi Nordic,
My firmware is done and v1 beta is release, i will use it to flash my final production first batch with it.
What are the several good pratices to create...
Hello again,
I am trying to use the nordic PPK2 to estimate the battery capacity I would need. I would like to measure for a longer time in order to spot any strange behavior...
I am developing a simple battery powered Zigbee light switch (sleepy end device) using nRF Connect 1.91. After successfully joining the network and accepting a bind request...
