Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello,
I have many board of nrf9e5 IC's,
But in nordic company it's discontinue,
It had long range and easy to set,
Now which product is like this?
I need part number...
Hello,
I am using the nRF52840 DK (same applies also for the dongle). The setup is quite simple. I have two nodes on my desk, one transmitting packets and the other receiving...
Hi
I have combined the ble_app_uart and libuarte example. The combination works "nearly" well.Transmit is ok, but when receiving characters over UARTE, no NRF_LIBUARTE_ASYNC_EVT_RX_DATA...
I see a square hollowed out area in the middle of the newly released questions about nrf5340 audio DK PCBA. What is the design purpose of this hole hollowed out area?
Hi
I'm on the very beginning stage to ncs for vscode.
I followed the course to build my first blinky example, but failed always.
I double checked my step and all the...
Hi,
I'm using nRF52832 development board with blinky example and with PPK kit I'm trying to get the actual power consumption from the development kit.
I think the actual...
We are working on a project where we have space constraint. We are placing AMS AS7038 , which is a Biosensor Solution with Embedded ECG Channel + Analog front end, just on...
Hi,
1. I tried to test AGPS, but an error was reported. The test results are as follows:
Why is the error reported? Is it that this routine does not support AGPS, or is...
Hi! I was wondering if I could use an SWD connection to recover a bricked chip. This chip is on a custom PCB that has pins allocated for SWD.
The chip itself is stuck at...
I'm looking for assistance or example sources of being able to dynamically control the Nordice device subsystems power. i.e. the serial uart used for the Zephry shell. But...
HI .
Two questions for the nRF52840, please have your comments, thanks. 1. Does nRF52840 Zigbee support SEP 2.0? 2. Can nRF52840 Zigbee be replaced with other protocol?...
Hello ,
I am facing issue while building Building example DFU application 'secure_bootloader_ble_s132_pca10040'
I am using SEGGER Embedded Studio IDE, and while building...
Good afternoon, I am new to nordic sensors. I would like to develop a phone application using Android studio that reads accelerometer values from the Nordic 52. How could...
Hello,
I am using nrf52840 with led blinky example for power consumption but it consumes 0 micro amp so i think reading was not correct so how can i troubleshoot this ....
Hi,
in my application I have setup the nRF52 to wake-up from deep sleep if a low value is detected on either of two GPIOs (4 and 5). What I'm trying to achieve, is to be...
