I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Is an adaptation of https://github.com/microsoft/Windows-driver-samples/tree/main/bluetooth/serialhcibus for the Nordic / Zephyr hci_uart sample available?
Like https:/...
Hi,
I work with win10 laptop, Toolchain nrf Connect SDK 1.6.1 on a nrf5340dk. I use peripheral_uart sample.
I follow the guide:
https://devzone.nordicsemi.com/guides...
Hello,
I have made a lot of work with nrf52840 microcontroller and i am in pre-production stage.
NRF Connect is not loading in vs code.
I have tried to uninstall/reinstall...
Hey,
I am using an HID keyboard + keyboard toggle in my project,
When the nrf connects an iOS phone, it takes control over the phone's keyboard.
To release the kb we...
Dear ,
I am using the nRF52833-DK development board with the NCS1.7.0 SDK.
I am trying to get a PWM waveform output at 50% duty cycle with 409.6kHz frequency based on...
Hi,
I have a NRF52840 USB dongle( https://www.nordicsemi.com/Products/Development-hardware/nRF52840-Dongle); is Any possible to flash NRF52840 dongle with PTS Firmware Upgrade...
After connecting to an nRF9160 using SEGGER tools (J-Link RTT Viewer v7.62b), excess power consumption is observed until the device is reset (via `nrfjprog -r`)
First the...
Hello,
The following is for a custom application but I have also tested this with the base peripheral_uart example with the same result.
I have an application which uses...
NRF52820
PAN1781 EV Board
Segger Embedded Studio 5.62
nRF5_SDK_17.1.0_ddde560
S140
Hello,
I'm currently working on an indoor positioning system and as the title...
Hi,
I compiled an application that should start at address 0x40000. However, executing an OTA DFU always places the application at 0x26000, right after the softdevice. ...
In a previous ticket on another topic this question came up. Given it was a tangent to the original topic of that thread, and I think it would be helpful to others, I decided...
OS: Ununtu 20.3 LTS - Kernel: 5.4.0-109-generic
Software: Power Profiler launched through nRF Connect for Desktop v3.11.0
Hardware: Power Profiler Kit II
Problem: Cannot...
