hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
I'm having issues using the debugger on the nRF9160dk.
Here is the log that is output when I try to program the on-board 9160 with the command, nrfjprog --program <path_to...
Hello
I am trying to figure out the ram retention on my nRF52-DK using SES and SDK v17.1.0. I've run through the example ram_retention , and studied a topic in Nordic's...
Hi All,
My development IDE for BLE based firmware is Visual Studio Code.
SDK download for this version is 1.9.1 zephyr based.
I have select the example code "nrf/samples...
I'm using the nRF52832 with FreeRTOS and nRF5_SDK_17.0.2 on a custom board.
I am using a peripheral from a third party that uses Flash storage for certain parameters.
...
Hi Nordic,
I have 2 devices - nrf52840. One is Central and another is peripheral. I want to set a quicker data response time - shortest connection interval. As far as...
Hello,
as I see , many in DevZone have had a problem like this: we tried to merge twi-functionality into the basic ble_app_uart example. We set proper defines in sdk_config...
Hi,
we are developing a way to define through code a zigbee device composed of multiple endpoints, based on nRF5 SDK for Thread and Zigbee v4.1.0. The program can be flashed...
Hi all,
I'm trying to increase BLE throughput of ble_app_uart example (from official SDK16/ s132).
I've searched quite a few tutorials on which parameters should be...
Hi,
We need an detail description about uint32_t dev_config used in int i2c _configure ( const struct device * dev , uint32_t dev_config )
(zephyr i2c: https://docs...
Hello everyone.
I am beginner dev. I wanna run Serial Example Mesh and received data from BLE sensor. Can you support me complete this Project.
Thank you so much!
I'm testing a simple application based on the UDP/CoAP example. It samples some peripherals and ADC channels, these values are then packed into a CoAP message. This CoAP message...
Hi:
I want to use saadc peripheral,when i run the example "nRF5_SDK_17.0.2_d674dde\examples\peripheral\saadc",it worked well,but when I want to port this example to "nRF5_SDK_17...
https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/nrf_dm
I used the demo linked above to test RTT and DHCP respectively. Within two meters, I found that...
From the DF spec, we know that the connectionless AoA puts the CTE signal on the periodic synchronous adv, why, and what is the benefit. Is it possible to send CTE in extended...
Hi,
I am using nRF5340DK for development. Currently, I have two problems:
QS1: When I use fun nrfx_gpiote_out_toggle(), it reports Assert error on NRFX_ASSERT(! pin_in_use_by_te...
