hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hello,
I am using PCA10040 DK for programming my custom board which is having the NRF52832 controller. Until yesterday afternoon, I was able to program my board using NRFgoStudio...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
Hi,
For the first time iOS App interface with BLE device. But after killing and re-opening of iOS App connection not established. Can anyone share me the code from iOS App...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
Dear, I have bought the nRF5340 DK. I have installed nRFConnector and Segger Studio. Now, I want to test Blinky project. I connected a USB cabel to USB connector which is...
I have a receiver , transmitter application. I use a custom board as transmitter. I would like to use pca10040 as receiver but currently i use it as debugger to my custom...
Hello, I have connected a LR1110 module to a nrf52 (PCA10040) development kit using Arduino connectors. Anybody written a simple application regarding the interfaces?
It...
Hi,
Our company has produced a batch of BLE products, and the 10uH inductor model used above is SDFL2012S100KTF. The rated current is not as large as the current value...
Hi,
I close the uart log and open the rtt log
why uart log can be used still?
why rtt log display error state?
I set the log config like this:
I set the test...
Hi all!
I'm testing the new development branch about wireless syncronization project.
This is my issue:
https://github.com/nordic-auko/nRF5-ble-timesync-demo/issues...
hi
i have this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_timer_cnt_get (referred from max30105.o).
in this code part.
the example is...
I have a program that runs great on the dev kit, however after uploading the code to a custom board based on the nRF52810, it does not seem to run.
I upload the code by...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
