I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
I am trying to use the NRFx Softdevice controller, with Rust and the nRF5340. I have successfully initialized the library, but when I try to start to start advertising the...
Hi! I'm unable to connect my development kit to a network with the provided iBasis SIM card. I'm located in Bristol UK. According to this [ https://ibasis.com/solutions/iot...
To provide feedback to the user through the LED state, I would like the behavior to be something like this:
If the nRF52840 Zigbee device is unpaired and ready for a ZC...
Hi support,
I'm currently having issue trying to program a nrf52833 device using Jlink mini on mac. I have no problem programming the device using a pro Jlink on windows...
Hi,
I'm trying to use examples. The ICM42605 example does not work.
I get the following errors.
There seems to be an error in the code below.
It was tested with...
Hello !
I have found that error free decryption ( MIC error) on fly depends from S1LEN configuration value.
S1LEN have valid range value for each radio mode
2Mbit 1...
I'm getting an occasional NRF_LIBUARTE_ASYNC_EVT_OVERRUN_ERROR, it often takes over 24 hours to reproduce, and the libuarte appears to be generating garbage after the error...
Hello Sirs
I am using NRF5340 chip in my custom board to use the BLE radio and uart hard ware at the same time. The sample code which has been used for this purpose is ...
I have a BLE device with a MIC, which collects voice data and coded to BroadVoice 32k.
So I want to design a central to get this voice data.
What I think is use 52840...
Hi,
Why do all of these AT instructions fail?
1.AT%XPRODDONE=0
2.AT%XPRODDONE=1
3.AT%XRFTEST
4.AT%XEMPR
Thank you for all your assistance. Kind regards, Peter...
Hi,
Since adding a custom board to a app from a sample, the Flash button:
Has stopped working properly.
When i press it, a build is initiated, but the flash does not...
Hi,
I used this example to develop code for a low power delay function. This code uses RTC1 with frequency = 32Hz to create an interrupt every 5 seconds and event handler...
Hi,
I have been programming my custom board using SWD on a DK. It worked fine when I tried blinky example, however, when I tried nrf_ble_uart example, it stopped at the...
The documentation on how the nrf mesh app adk works is impossible to follow and understand for a junior dev like me to make something close to a working app.
I might be...
Hei!
Mid code development my ability to flash new versions went away. The only clue I have is that W11 installed some new drivers, but I'm grasping at straws. I have screwed...
