I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi,
I am debugging an Application running on a custom board that uses the NORDIC nrf52832 processor connected to an IMU over twi. I am using SDK17.0.2
I find WDT is kicking...
Hello Nordic Team,
I've been having good success with the 52840 and been slowly migrating a lot of my projects to the chip. While I await modules to arrive from a supplier...
I'm trying to use 9-bit UART communications with the nrf52840 using nRF Connect SDK v1.9.1, but I'm getting an error -134 when I call uart_configure().
When I use UART_CFG_DATA_BITS_8...
Hello,
NCS1.9.1, nRF52840DK, Windows10 X64, VS Code,
1.
i want to read voltage from RT_ADC pin (P0.04),
and than converting NTC thermistor value to Temperature.
...
Hi,
My setup include a nRF52840-DK board that has an ESP32 WiFi module connected to it via UART. The idea is to source the new firmware from a server located in the cloud...
Hi, I'm doing experiments with Bluetooth direction finding. I am using the example of the nRF52833 development board, and I have obtained the IQ representation of CTE and...
Hi I am using the aws_iot example on the nrf9160 DK.
I have opened the zephyr.dts file and in the section uart0: it has the following
I've reached this point trying...
Hi,
I am looking to connect the ds18b20 sensor to the nrf9160dk. I followed this post, but when I tried running it, I was getting a "create_nordic_project.py failed (1)...
2022-04-12
Hello Devzone Community,
I have a couple questions regarding availability of nRF9160 LTE modem settings PSM and eDRX. Question (1) If my local celular carrier...
Hi Nordic Support,
I'm running into an issue with ncs v1.8.0 directing log and shell to RTT backend.
Objective: Using nRF NCS / nRF52840dk - I want to dedicate 1x UART...
Hi,
I have opened a ticket with Kenneth and verified it by mistake. It is now locked. I have done the changes Kenneth asked me but it didn't resolve my problem.
thanks...
Hi,
I am connecting my nrf9160 based system to the nRF Cloud and sending data from it.
I got the cloud to show the RSRP values that I sent it through the following JSON...
NCS 1.8.0
Modem FW 1.3.1
For other products I've worked on with cellular modems, we would add in back-offs to the firmware in the case we failed to open a PPP session...
