I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
Hi, I have been learning my way around SES, nRF Connect SDK, nrf52-dk, and the sample projects for some time now.
When I wish to open another sample project, I follow the...
I program the uart example in my board nRF51 dk. I put a osciloscope in pin 9 and the signal is a square wave between 0 al 30V. So i think that the protocol is RS232, is this...
At a rate of 1M, the receiving sensitivity of the Bluetooth chip was tested, and during the test, it was found that the sensitivity may decrease whenever the frequency point...
Hi
We are working on an algorithm applicable to the indoor positioning of ships. We want to improve the algorithm further on top of the existing algorithm for Bluetooth...
I'm on a Comcast cable modem connection. When I've tried to pull up this site over the past few days, I've gotten "The page cannot be displayed because an internal server...
Dear nRF DevZone,
I have question regarding Zephyr k_sleep() function and NRF52840 timers.
I am developing an application for nRF52840 SOC and for that I am using nRF...
Hello. I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
I want to pair from "Settings"-> "Bluetooth" of iOS (iPhone 12 Pro). For pairing...
Hello,
I am developing an application that requires use of some of the traditional C "stdio.h" functionality. My current development setup is the nRF5340 DK running Zephyr...
I'm using sdk for mesh version 5.0.0, sdk version 17.0.2 and my board is nrf52840-DK.
How can i keep mesh config after wake up from deep sleep( system off).Plus, when my...
Hi,
This morning when I tried to access devzone, it says I have been IP banned. I have the same issue as this ticket:
https://devzone.nordicsemi.com/f/nordic-q-a/86922...
Currently running NCS 1.7.1, SUPL client 0.7.0 and MFW 1.3.0 it has stopped connecting properly from the last time I've played with it:
Not sure what's up there..
...
I am having trouble powering my uicc. I feel like I am just looking for some setting, but I have not found the right one yet and I am at a loss at this point.
What I have...
I used direction finding rx/tx examples(get 45 points of IQ data). I used the ref period IQ data (8 points) can caculate base phase and the phase velocity(setting is 500KHz...
Dear all,
I have struggled this problem over a week.
I am working on our product, which need to prevent other strangers to connect to our device. After search on the Nordic...
