void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Dear Nordic engineers
I study the AES examples.I have a question and would like to ask you.
I study the aes_ctr examples.I found that this program use two functions to...
Hello. I am trying to change the UUID value of a service and characteristic of my nRF52 to have a custom value. I have successfully done this in firmware and it has been found...
Hello everybody,
I am currently working on a project in which I need to read some data from a glucometer. Until last week it was working fine, however I stopped receiving...
Hello,
I installed nRF Connect SDK V2.0.0 using "NRF connect for Desktop"
Now I can't open nRF Connect SDK projects on segger embedded studio.
It showing only VS Code...
I am using Nordic Serialisation library, with a nrf52480 chip as connectivity chip and a m4 arm core custom board as Application chip. I am able to establish gap connection...
Hi,
I'm trying to get a better understanding what causes some unexpected current peaks while nRF9160 is in RRC-IDLE with the NB-IoT mode. I have been experimenting with...
I am trying to interface the Grove 4 Digit Display(TM1637) with the nRF52840 DK.I have successfully interfaced it with ESP32 and get clear output after researching for the...
Hi,
We develop in an OpenSuse VM so that we all have the benefit of only having to setup the tools once. Segger Embedded Studio was building our variant of the DFU Bootloader...
Hi,
I'm using the nRF52840 SDKs (15.0.0) and nRF-IEEE-802.15.4-radio-driver( 1.1.0 ). BLE and the CoAP baseed on 802.15.4 work fine, but when I call this function
void...
Hi,
I'm using SDK v14.2.0.
For the workaround of [107] RADIO: Immediate address match for access addresses containing MSBs 0x00
I'm trying to avoid the addresses...
Is there a way to read the mac address from the serial tty of an nRF52840? I have multiple dongles programmed with the BLE sniffer (nrf_sniffer_for_bluetooth_le_4.1.0) and...
This is my first time developing for Nordic processors. I am using Zephyr 3.0.99 with the nrf52810 on a ublox BMD-330 eval board. I connected a W25X20CL 2M-bit chip via the...
