here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi again
I have used nrfConnect to create an application from sample, the sample being peripheral_hr_coded
I have placed my custom service into the app, and it works...
Hello, I am trying to measure the input voltage on an nRF52833 and it is not behaving as expected.
The following code is taken from here and works as expected on any nRF52832...
Dear Sir.
I am using the cJSON driver .
When it comes to string it works fine .
However when I use integer and swap the lines
//cJSON_AddStringToObject(root, ...
I'm sorry my English is not good enough.
I am developing a product that works as a BLE peripheral using nrf52832 and NCS1.6.1.
In addition, the following statement is...
Hello,
I am trying to establish a mesh network with two nodes(self provisioned) simulating the Light and Light_switch examples without the provisioner. My plan is to play...
Fairly new to nRF Connect SDK & Zephyr although I have worked a lot with NRF5 SDK
I'm at a bit of a dead end here. I trying to setup a way to repeatedly read out data from...
Hello,
I would like to use littlefs in out Project and it seems to be very usefull. I read several documents and have the sample running on the eval board. But there is...
Hello,
I'm using the power profiler to perform current measurement of our IoT device. It appears to work well when running for a few minutes capturing. When I wrong for...
I am trying to use SPIM2 on an NRF52840 based board. The SDK is 17.0.2.
For the life of me I cannot understand how to 'consistently' determine the values to be specified...
I'm trying to modify the HTTPS sample to connect to Google Cloud Functions but I keep running into this issue where connect would fail.
1. I have disabled TLS peer verification...
We have a running project with nRF52840 + S140 7.2.0 - SDK: 17.0.2 + Bootloader.
I need to change the size of our bootloader in a production environment. This update must...
Hello,
We are currently certifying our module for Verizon in the US. As such, we are updating our software to work with MFW v1.3.0 and the corresponding NCS version v1...
Dear Nordic,
we developed firmware based on S112 and SDK 17.1.0. We have a problem with poweroff routine: at poweroff the status LED is ON.
this is part of our circuit...
Hi Team,
I am using nRF52840 on our custom board. I have enabled SMP for DFU and SMP image management in my build. DFU was successful for the 1st time but when I try to...
