void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I recently started with nRF52840-DK, Zephyr and nRF Connect SDK (v. 1.9.1). I want to test extended advertising, that's why I use the periodic_adv example coming with...
Hello,
I am using the vl53l5cx TOF sensor and implementing the ULD using zephyr. My setup is a bl654 board using zephyr on sdk 1.9.1. However I am running into an issue...
(replica as the previous post was archived by accident...)
Hi,
I'm trying to incorporate LittleFS into our development. We are relying on services provided by TF-M....
Hello,
first of all i am a new user of NRF microcontrolers and embedded systems. I ve been searching on this forum for a simple PDM microphone example and although there...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
Hello,
I am trying to figure out which example is the closest fit for our design. We are using a 2 processor solution in our product, and the firmware for the NRF52832 has...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
Hello,
I want to test the throughput of Isochronous Channel using ncs sample code "iso_connected_benchmark". So far I can successfully build the code and run in central...
Hi,
I'm trying to save system uptime when the watchdog callback occurs.
The NVS functionality works when calling nvs_write elsewhere in code.
Calling nvs_write inside...
Other Configurations:
prj.conf
# General config
CONFIG_LOG = y
CONFIG_LOG_DEFAULT_LEVEL = 4
CONFIG_STACK_SENTINEL = y
CONFIG_NEWLIB_LIBC = y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
