void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I am trying to enable UARTE0 on BMD-330 module. The serial config looks like this
# # Capabilities # CONFIG_SERIAL_HAS_DRIVER=y CONFIG_SERIAL_SUPPORT_ASYNC=y CONFIG_SERIAL_SUPPORT_INTERRUPT...
Hi,
I tried porting LC3 to my own 5340 project with reference to the SDK(nrf5340_audio_nrf5340_audio_dk_0.4.0), but I had a restart problem when initializing LC3
sw_codec_lc3_init...
Hi, I have a mature product that is programmed with a J-Link compact, I have 4 different PCs to program and a custom UI that uses command line instructions to flash PCBs....
Hello,
I'm currently developing on an NRF82832, I'm using a Black Magic Debug Probe to flash the firmware and the bootloader. I use Linux.
I have a working firmware...
Hi,
I started using nRF Connect SDK in VS Code recently. Everything works well, start a new Application, configure a new board, build, and flash.
While I found "Go to...
Hi,
I'm working on modifying the secure bootloader (SDK 17, nRF52840, s140) to store the old app before the new app is programmed into Bank 0 (see this other thread )...
Hi,
We have a design for a battery powered tag using a nrf52833-QIAA. I saw in a post from a couple years ago that you widened the DCCH inductor tolerance to +-20%. I...
Hello ,
I am trying to use NFC pin p0.10 as WAKE up pin , using nrf_gpio_cfg_sense_input(Btn, NRF_GPIO_PIN_PULLUP, NRF_GPIO_PIN_SENSE_LOW); this code. I have defined CONFIG_NFCT_PINS_AS_GPIOS...
Hi,
I double-checked that when NordicUpdate_is_update_mode() returned false, I can still use the iOS Device Manager App to perform DFU.
I thought users needed to press...
Dear Nordic support Team
I have a question regarding the performance/specification of the RF front end of the NRF52 series chips. I noticed that the question "Is there an...
Hi, I'm testing the current consumption on a nRF52810.
I use PPKII to measure the current that the chip draws.
The software does the following.
Wakes up every 1 second...
Hello,
I am developing nRF52832 with SDK 16.0.0, ESB prx example.
ESB prx receive BLE and send it to UART.
UART is configured to 1000000 baud, which is maximum rate...
Hey,
I am trying to set up an application that generates interrupts on a total of 11 buttons. Setup is pretty straigt forward, for which I use the following functions for...
Hi all,
I'm using the PPK2 to measure the current of our IoT device. To get the data from my PPK2, I wrote my own software in order to integrate it into our test setup....
