I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I've created a new sandbox project for a nRF9160DK that requires a SPI Master for testing a Flash part. Since I already have "working" SPIM code in a different Segger project...
I am using the beacon mod example with my nRF52-DK to calc battery life. All measurements are taken with PPK2 (a great tool by the way), but in the PC application my timestamp...
Is there a process in place for updating a controller only build via the HCI? My current set up is a 9160 as the BLE Host, a 52820 as the BLE controller, MCUs are connected...
Hello, Im a little confused about the nRF Connect SDK ecosystem.
Currently Im using SES with cloned nRF SDK 15.0.3 for nrf52811, however I would like to start using https...
Hi
I plan to enable hardware flow control in the coprocessor code. After successful compilation and burning, I will use Ubuntu to start wpantund and an error will be reported...
We already made working code with NRF5 SDK. It has added three characteristics to send data via UART from a MCU. Each characteristics for separate purposes, for eg. Characteristics1...
Hello,
I'm selecting crystals for a project with nRF52832QFAA.
I noticed that on the spec the drive levels of HFXO and LFXO are 100uW and 1uW respectively. Should the...
Hi,
I'm trying to integrate https://github.com/nrfconnect/sdk-nrf in version v1.9.1 in my baremetal application (nRF5340 NET and APP CPUs). Where can I find the startup...
Hi,
we are using an nRF52833 for an application where we have a sensors, a USB interface and an SD memory device.
We would like to write and read back sensor values to...
Hi,
I am following the step by step tutorial " Getting Started with Secure DFU Bootloader Step by Step guide "
Before following the above guide I compiled ble_app_blinky...
Hello,
I'm trying to use the VL53L1X Time of Flight sensor on my nRF52DK, but I experience some problems.
Previously, I've successfully used the VL53L1X with an Arduino...
Dear Sirs:
We use nRF52810 as the key chip in our product, however, we need it to be central or peripheral based on user's option.
So, we would like to apply softdevice...
Hello!
I am currently working on doing the smp_svr sample:
I have done these commands so far (on created from sample application):
west build -b nrf52dk_nrf52832 -d...
Hello DevZone,
I am using Segger embedded studio with multiple build configurations for the two chips and I am having some issues to get the program to compile my nRF52810...
I have tested the sdmmc driver yesterday with both, CS Pin tied directly and via an external i2c port expander. TCA6408A.
Worked like charm, but today I wanted to to some...
