I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
Hello,
I am using nRF52833 based BE33 ( Celium Devices ) and using nRF52SDK17.0.2. I am trying to implement WDT and expecting to occur its event when the module becomes...
With the release of the Bluetooth 5.2 standard, also came the introduction of BLE Audio.
Since I am evaluating a SoC for bluetooth headphones, I stumbled upon the fact that...
I have an nrf9160dk setup with the bluetooth-hci-lpuart flashed to the nrf52 chip and a bt peripheral sample flashed to the nrf91. This works as expected. However, I am trying...
Hi Everyone,
We are currently stumped and are looking for guidance. A brief overview of what's needed from our client are as follows:
1) From the nRF mesh app, send...
Hi,
im using sdk 17.1 with segger embedded studio v6.2a and nrf52840. I am trying to use the uart example and it gives an error no name type found "__printf_tag_ptr". I...
I encountered a problem in configuring the general switch model. I want to configure the group address at the beginning. I set the dsm_address_publish_add（） and access_model_publish_address_set...
When I was adding the ID of the sensor, I found that the specific name displayed on the Bluetooth app is not my own name. Is there a special definition for this ID? I checked...
Hi
I'm looking for a clear statement about to do or not do modem firmware downgrades on production devices.
I know that
nrfxlib does not mention anything about modem...
Hey, I'm working on a real-time body motion capture project and using nRF52832 as BLE MCU. In the system I have 3 IMU sensors to transmit sensor data to an Android device...
Hi,
This is a repeat of case 279137 but I see no answer to that so here goes again...
I am building sample Zephyr applications in VS Code. Everything was working fine...
Hi!
We would like to be able to send two separate dfu-packages independently, one hex/pack containing our main application and one hex/pack containing data to be read by...
HI All,
We are using NRF52832 for our project.
1) We are using System ON mode to put NRF52832 in to sleep mode. We are able to put NRF52832 in to sleep mode(System ON...
Hi,
I am working with the nRF52832 DK. I want to program a couple of ICs with SPI every 2 ms. I have successfully configured the nRF as SPI master and I start the SPI transfers...
Hi All,
I wanted to look at the power profile for my nRF52840 dongle, I installed nRF connect and installed the Power Profiler. But as I want to the option to connect the...
