The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
Hi,
Is it possible to be in connected mode (exchanging data) and also advertise data packet (on primary channels) between two BLE devices (so, in both the modes) ? Is there...
When using nrfjprog over an IP connection, `--ids` never returns a value. This is frustrating as the Zephyr nrfjprog runner uses this command to determine if there is a board...
Hello !
In latest errata, https://infocenter.nordicsemi.com/pdf/nRF52840_Rev_3_Errata_v1.1.pdf is not so clear all details of this anomaly
[254] RADIO: External PAs, FEMs...
My laptop is running the latest macOS 12.4. It is a 2021 Macbook 14" with M1 Max.
I updated nRF Connect For Desktop and Toolchain Manager to the latest versions, then I...
I am trying to port a timer over to the nrfx_rtc driver and I can't seem to get it to start counting. I'm sure I'm missing something small, but I'm not seeing it. SDK 17,...
Hi,
I have a medical device where my mother board has a NRF52840 chip which communicates with a Android Tablet through blue-tooth. We find it gets connected with few tablets...
Hi, I am working the Zigbee in nrf connect SDK 1.9.1 I am running light_bulb, switch and coordinator examples
I want to change the panid , Short id, via proj.conf
how...
We have an nRF5340 application that builds fine for our custom board. However, it is not very straightforward what steps need to be performed to enable FOTA updates. I have...
Hi,
I am using an nrf5340 with nrf connect sdk v1.9.1. I need to calculate the duration of an event with nanosecond precision, so I am using an nrfx_timer at a frequency...
Hi,
Greetings!
I am using below setup
nRF52832
Mesh SDK 4.0.0
SDK 16.0.0
Application Example: light_switch_client_nrf52832_xxAA_s132_7.0.1
Issue:
Using above...
When I run TX tests with the AT%XRFTEST command, I can start the TX test without any problem but then the modem stops responding to AT commands. For example, if I send
...
Hello, I'm in the process of attempting to implement Eddystone EID on the nRF52805.
It's been a bit of a nightmare, so I'm finally taking the bold step to make my first...
I am using SDK 17.1.0 with an nRF52832 design similar to the P10040.
I was previously using the original timer application and things were looking good. I decided to upgrade...
Hi,
1. Please provide me with an example in which UART0, UART1, uart2, and uART3 are enabled
2. The sending and receiving rate of each UART must reach 1,000,000 baud rate...
We are porting a project from SDK 11 to nrf5 SDK 17.0.2. We have also used a couple of different versions of SDK 15 extensively on several different products.
Our code...
