When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Hi
I can't set CommonName in the attributes list while generating a private key, it gives an error:
Omitting CN it works fine:
What am I doing wrong?
Thanks...
Hi
I have a question concerning AOA.
I have already make a tx (with nrf52833) and a rx (nrf52833 too) and i succeed to receive the CTE and the IQ sampling with the antenna...
Hello ,
my team and i we are trying to set a communication by UART between two nrf52840 µC , with one of the µC we have done a communication with a nucleo board which supports...
Hello all,
I have made a simple app that runs in loop on the nRF52DK, in general it reads data from the sensor via twi and turns on the leds ...
When the program is run...
Hi, i am developing Zigbee window covering device on nrf connect sdk 1.9.1v which has 2 endpoints, but i am face issue when zigbee command is received and
device_interface_cb...
I have Ebyte’s E73-2G4M08S1C (nrf52840-QIAAC0/ aQFN73 module) where P0.19, P0.21 and P0.23 are not wired out :(
So, my question is which other pins could use / not use instead...
Dear Nordic Community,
I am trying to implement a porting of micro-ROS framework on the nRF52840 chip. As stated in their tutorial , the framework is compatible with the...
Hi,
I have started learning nRF5340 recently and have got the development kit as well.
I compiled first example of "peripheral_uart" but I am not able to program the board...
I have the ble_peripheral blinky example running, and I have a separate project with the USBD working fine (based on the usbd_cdc_acm example), but when I try to merge the...
The advtising data is 050501020304.That mean
advlen=0x05,
advtype=0x05,//BLE_GAP_AD_TYPE_32BIT_SERVICE_UUID_COMPLETE
advdata=01020304.
we want to set the 32-bit...
Dear Nordic Engineers
I use the NCS V1.9.1.I would like to building the openthread\coprocessor project on the nrf52840_dongle.I read this page: https://developer.nordicsemi...
Hi,
I found that runing a piece of code costs 490.21 us when OpenThread is disabled.
However, after OpenThread is enabled, the time changed to 746.3 us as shown in the...
In SDK17.1.0, there is an example called libuarte. Here the example uses UARTE0 to send and receive serial port data, and he is defined as follows.
NRF_LIBUARTE_ASYNC_DEFINE...
